Jump to content
SAU Community

Recommended Posts

The auto is fine for the drags, but if your planning on giving it a heap of power then the manual is much better. You can think about putting in a stall-converter to help with launches, but the manual is much more fun to drive.

See'ya:burnout:

The auto is good. It is very weak tho'.

The thing will need a strong rebuild, a shift kit of some kind, a larger trans cooler perhaps and a hi-stall built.

Alternatively a trimatic like the VL turbo's run would be a much better bet for serious power. The performance rebuild of a trimatic or turbo350 is very cheap, even after the custom install its going to work out cheaper for a tough as nails trans.

The dude TRY9, i think it was him, had a trimatic fitted to his RB and was doing 10's with it from memory.

Auto i guess easier just for dump and go... no brainer generally.

If you do up your engine and you end up blowing an auto box you're going to require a whole new one or a rebuild (expensive). I was quoted once $1800 for a new auto fitted, and that was for an old R31 (guess same as VL box?). Hate to think how much for R33.

In a manual most of the time you just blow the clutch (much cheaper!), replace for a bigger one and keep driving.

I took an auto for a drive when i was looking around. wasn't very happy at all. It didn't pull all that hard. it was in good condition overall tho'.

With manuals you can stretch the gears out more too.

But yeah autos are way cool for drags spesh for consistent times.

HI Stall big turbo combinations work really well, say your turbo doesn't make boost until 3300rpm, by getting a 3500rpm HI Stall as soon as you put the foot down your at 3500rpm instantly and at boost. There is a down side to it though, wheel spin is quite vicious and fuel economy is down while cruising as the convertor is basically slipping until 3500rpm.

Every Auto has a stall converter but there usually set very low like 1500rpm, a HI stall convertor just replaces the stock one, and no it can't be switched off coz it's sort of like a clutch that won't fully engage until the set rpm.

The car won't always be at 3500rpm(eg) but at the slightest press of the accelerator the rpm's will jump up to 3500, that's why the fuel economy is effected.

An Auto is the way to go

Think about the developments in motor sports today, all of the big ($$) teams are using auto boxes with manual selection through paddles/buttons on the wheel. Whilst I would agree that a stock R33 auto isnt a quick shifting beast, with a little work it has great potential.

The idea that you can hold gears longer in a manual is crap. I can select a gear and keep it there until the Porer FC's rev limiter cuts in (not a nice feeling), but more importantly you can set the auto to shift at the correct rev point. (no more going over the top of your power curve, and costing you time) every time without you having to watch the tacho (which moves too bloody fast anyway :-P )

As mentioned above boost comes on when needed via the correct torque converter.

The other advantage is that the throtle is held open for the length of the run (no need for the blow off valve to work) and hence no spool down on the turbo. (ie boost from foot down to foot off)

As to the idea or poor durability my R33 puts out 180 RWKW and has given no problems. (stock auto) My new auto (sharper shifts, higher stall converter) was in a car that was constantly given stick and put out over 230 RWKW.

My advice is dont listen to those who have not played with auto equiped skylines. (they probably dont eat quiche just because they were told once that REAL MEN dont eat it)

  • 10 months later...

I must say I went from a vl auto to r33 manual and manual kicks ass. So much more involved, used to get bored when driving an auto. The manual is so much more active and involved, like a real race car

I think manual is great for dragging too, everyone loves the chips in 2nd and 3rd when u do a quick shift :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...