Jump to content
SAU Community

Recommended Posts

Hey guys,

Is it worth rebuilding my own RB20DET in my R32 or would i just be better off going and getting a semi-stock RB25DET and putting in in my car.

In terms of the power output which engine is the better one to work?

Can RB20DET after market performance parts be picked up easlily in Australia?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/100446-modified-rb20-vs-stock-rb25/
Share on other sites

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

I keep breaking rb20's so i went to an rb25 and have not had any issues at all...

Remember for power vs dollars spent it goes like this

1. RB30det/t

2. RB26det/t

3. RB25det

4. RB20det

I mean if you have a 20 then go to the 25 if you have a 25 and want more go to the 26 and if you have a 26 and want more then go a built 30....

Know what i mean....

Its such a matter of personal preference and what you want. If i had $5,000 to spend on a mostly stock GTST i wouldnt bother with an RB25. At best you will end up with 200rwkws and probably have less average power then if you put a 2530 on your RB20.

If money really isnt a problem, or killing an RB25 not that scary a proposition then you really cant argue against going for the biiger displacement Nissan engine, as its not as though they are scary engines liek the 5.4L Ford V8 which dynamincally arent good engine.

...as for strength, give me a std RB20 over any other RB engine. If your killing RB20s then i would be so bold as to say its not the negines fault but the drivers, as they take an absolute hammering, provided you keep an eye on temps, fluids etc

I keep breaking rb20's so i went to an rb25 and have not had any issues at all...

Remember for power vs dollars spent it goes like this

1. RB30det/t

2. RB26det/t

3. RB25det

4. RB20det

I mean if you have a 20 then go to the 25 if you have a 25 and want more go to the 26 and if you have a 26 and want more then go a built 30....

Know what i mean....

i woulnt put the 26 cheaper than a 25, my 26 im building now is costing a LOT more than my RB25 did <_<

your question is wether it's worth REBUILDING an Rb20 or buying an RB25?

out of those 2 options only, I'd buy a 25.

however, I say that if you have enough money to BUY and fit and tune an RB25, you have enough money to build, fit and tune an RB30det.

which ofcourse is my pick of the RB engines.

LOL, i read that, and i took it as

"I have the choice of rebuilding my RB20 in order to aquire enough power to put my car into outer orbit...or buy a std RB25 and have to wait for my neighbours dog to take a piss on a wild daisy, then another two days for it to die so that the power of a std RB25 would allow me to remove this weed from my lawn"

So i didnt think there was anything broken about the std engione?!?!?! But i am struggling with English since Xmas NYE celebrations

rb20 rebuilt with a larger turbo should provide some significant fun, not to mention with the money saved on a rebuild rather than buying a rb25 you will KNOW the exact condition of the motor and can go from there.

when you buy a used motor you are taking a gamble, it might last it might not its hard to say.

i swapped a rb20det into my s14 as here in the us we got shafted and got a 2.4l which makes 155bhp, and even tho i blew the rb20 i have no regrets and am in the process of building it back up.

i'm with ash..rb20's are crappy.. ok up to a certain point, but after that not worth spending too much money on them.

modded rb20 good highway cruiser from 100-200km/hr.. but amongst town I'd almost prefer an rb30E :)

your considering rebuilding your RB20 because it popped? Isnt that enough to steer clear and UPGRADE to RB25?

400rwhp is easily achievable and streetable on a RB25 as opposed to a RB20, I guess it depends how far you wanna take it...

Edited by _8OO5TED_

Getting a stock Rb25 is called "headroom" ;op

Even if it is as quick as a modded RB20, you can easily mod the RB25 and get much more out of it.

I recken you could chuck RB25DET NEO in the list there... stock 206kw for a few more dollars. =-]

The only people that will tell you an RB20 is any good are the owners that are either in denial or haven't seen the light of the larger displacement RB motors. :)

I don't care if you have an RB20 with a T78, give me a stock RB25 anyday, way more fun!

The again, there is only two real RB motors,

1. RB30DET (do it with cubes)

2. RB26DETT (do it with revs)

:)

See the light of the above motors and don't look back :)

RB20 was probally good for the jap taxi's though ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...