Jump to content
SAU Community

Eoi: Low Profile Jack And Jack Stands

NiCk-180

By NiCk-180,
in Group Buys

 Share

Recommended Posts

lwells Grand Master

lwells

Posted
Posted

I assume by jack stands you mean axle stands? Are they the cast or tubular variety? In regards to the Australian Standards issue, can someone clarrify if there is a distinction between A.S. approved and "complies with", because with many regulations there is a huge difference. Usually "complies with" implies that the manufacturer warrants the product meets the stated specification, whereas approved means its been submitted for inspection and documentation is issued to show the item has been found to meet the specification.

Just to add a bit more. From an Australian Standards policy document:

All Australian Standards are, in themselves, voluntary; however, between one-third and one-half of all Standards are referenced under State or Commonwealth legislation. A number of Australian Standards relating to the safety of consumer products or information about consumer products are referenced in Mandatory Standards under the Trade Practices Act (TPA).

The TPA is a Commonwealth law and controls the activities of corporations. State and Territory Governments also have controls on consumer products under their Fair Trading Acts which extend to the activities of sole traders and partnerships. In recent years, there has been considerable progress in harmonizing Commonwealth and State controls on the supply of consumer products.

The Mandatory Standards under the TPA control the supply of goods, as opposed to the usage of goods. For instance, State traffic laws require that cyclists must wear an approved bicycle helmet; however, the Mandatory Standard under the TPA ensures that only bicycle helmets complying with AS/NZS 2063 can legally be sold. If the usage of a product is controlled, but the supply is not, there is a possibility of consumers purchasing products in good faith that cannot be legally used.

Sorry for the hassle, but you can understand my concern given the possibility of serious injury should equipment like a jack fail. I am genuinely and seriously interested in purchasing; I'm not just tyre kicking for the hell of it.

NiCk-180 Apprentice

NiCk-180

Posted
  • Author
Posted
I assume by jack stands you mean axle stands?  Are they the cast or tubular variety?  In regards to the Australian Standards issue, can someone clarrify if there is a distinction between A.S. approved and "complies with", because with many regulations there is a huge difference.  Usually "complies with" implies that the manufacturer warrants the product meets the stated specification, whereas approved means its been submitted for inspection and documentation is issued to show the item has been found to meet the specification.

Just to add a bit more.  From an Australian Standards policy document:

Sorry for the hassle, but you can understand my concern given the possibility of serious injury should equipment like a jack fail.  I am genuinely and seriously interested in purchasing; I'm not just tyre kicking for the hell of it.

Yes i do mean axle stands. They are cast.

The jack is approved by the appropriate authorities.

*This is not an el'cheapo product*

just so you know frieght to NSW is aprox $32

If you have any other questions feel free to ask

cheers

Nick

lwells Grand Master

lwells

Posted
Posted

Nick,

Thanks for that. I managed to drag up the appropriate government document anyway: http://www.accc.gov.au/content/index.phtml/itemId/663755

Although the standard itself mandatory, compliance with the standard does not involve any submission and certification (i.e. the manufacturer certifies the product). So everything is hunky dory.

Soon as I get a little cash (hurry up ATO!), I'll shoot you a PM.

NiCk-180 Apprentice

NiCk-180

Posted
  • Author
Posted
Nick,

Thanks for that.  I managed to drag up the appropriate government document anyway: http://www.accc.gov.au/content/index.phtml/itemId/663755

Although the standard itself mandatory, compliance with the standard does not involve any submission and certification (i.e. the manufacturer certifies the product).  So everything is hunky dory.

Soon as I get a little cash (hurry up ATO!), I'll shoot you a PM.

no worries dude,

just spoke to the supplier is wiling to prove he has the apropriate certification

wolverine Grand Master

wolverine

Posted
Posted

my jack and stands arrived today in sydney as promised. nick called before sending yesterday and today to check the safe arrival.

two thumbs up to nick for the delivering what he promised.

(hi yogi000, i hope all goes well for you)

d00dz Grand Master

d00dz

Posted
Posted

Same here.. I just got mine delivered as said..

Top stuff, the courier dude was good too, helped me take the jacks all the way to the back of the apartments and put it in my garage.. I didnt have to loose a sweat.

As for Nick, great stuff too.. Easy payment in bank account on Friday and I got my goods today (Tuesday).

Cheers!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...