Jump to content
SAU Community

Recommended Posts

An atmo bov will increase the backfires as its venting air to the atmo instead of back into the air intake making the afm compensate with more fuel, which means car runs richer and backfires. It used to happen on 90% of my gear changes so I got rid of the atmo bov and went back to the std one, though when I downchange at 3000rpm or more it backfires too. Need to get an SAFC to lean it out a bit.

Ive always had it, figured the aftermarket ECU caused the majority of them. Then i got an atmo BOV and its increased slightly, probably hear 6 or 7 in an hours worth of driving. Doesnt really do any harm. ALOT of turbo nissans do it with aftermarket exhausts.

But if its doing it on 90 percent of your gear changes then thats just ridiculous.

And its not strictly a backfire in my opinion.... backfires cause people to hit the pavement (see Uncle Buck).... Skylines seem to just make nice snap crackle pop noises.

Red17

yep, i believe that this 'backfiring' as described is actually 'over-run'. I think it has something to do with the fluid (exhaust) flow through a pipe and the effect of massive changes in flow velocity as you change gears (i.e very fast gas flow to much slower)... sort of a reverberation within the pipe. This happens more with aftermarket exhausts due to the increased diameter resulting in a greater flow speed differential. Of course if your mixtures are rich then this will also cause exhaust noise as the unburnt fuel is ignited outside the combustion chamber.

This is only a guess, but i think it is reasonable given the aerodynamics i studied through my (unused) mechanical engineering degree... feel free to correct me if i'm wrong.

OK...youve given me some ideas...thanks.

Some great theories, and it's intriguing that others suffer the same problem.

It is actually a popping noise, rather than a backfire, still, it is a bit distressing. Is it damaging though ??

I do have an aftermarket exhaust...a Kakimoto NS309....but the problem has only recently started....possibly after I was stuffing around with the BOV tension.

I might try tightening up the BOV (an atmo) and see if that has any effect.

cheers Ozzy

same here ED!

The Skylines are known to run very rich. Up the boost and the ECU over compensates even more. Mine is starting to sound like a rally car on the up changes ( running 0.9 bar ).

Could be wrong but I definately though it was unburnt fuel from running too rich.

BUT it sounds COOL...RIGHT???

Maybe not 90% of your driving time tho, that'd be a little annoying! I can get mine to back fire any time usually, just nail it and the back off real quick, if no back fire, lightly tap the Loud Pedal and you should hear the fruits of your labour.

I think my plugs need replacing now, but that's OK...

Yeah its just a pop, not a huge backfire... yeah its cool, there is one corner on the way home if I get the green light I can wind it down from 80km/hr to around 40km/hr and drop it into 2nd and I got a nice pop out the back... I suppose if I had a dump+front pipe and no cat I'd get flamage :P

I bet if you put the standard BOV back on you wouldn't hear a sound...

Yes the ECU expects an extra burst of air from the plumb back which is expelled from the intake system, so it compensates for this by adding fuel. This also solves the mystery of why some after market BOV make your car stall (over fuel).

A mate of mine solved this by installing an AVO atmospheric/plumb back BOV (all in one).

But if you don't mind the sound, forget about it, it's doing any harm.

Have Fun.

Yesiree, it is mine.....thanks....I think it looks good too. It came from Japan like that....I believe it is a standard factory R33 GTR bar.....Its good in several ways....you can remove the bottom lip when its been scratched to hell and repaint it off the car....(the beast has Tein's all round and is set on the stops)....it also allows you an absolute shirtload of room for a FMIC....which will come when the MRS lets me spend some more (of my) money.

cheers Ozzy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...