Jump to content
SAU Community

Recommended Posts

An atmo bov will increase the backfires as its venting air to the atmo instead of back into the air intake making the afm compensate with more fuel, which means car runs richer and backfires. It used to happen on 90% of my gear changes so I got rid of the atmo bov and went back to the std one, though when I downchange at 3000rpm or more it backfires too. Need to get an SAFC to lean it out a bit.

Ive always had it, figured the aftermarket ECU caused the majority of them. Then i got an atmo BOV and its increased slightly, probably hear 6 or 7 in an hours worth of driving. Doesnt really do any harm. ALOT of turbo nissans do it with aftermarket exhausts.

But if its doing it on 90 percent of your gear changes then thats just ridiculous.

And its not strictly a backfire in my opinion.... backfires cause people to hit the pavement (see Uncle Buck).... Skylines seem to just make nice snap crackle pop noises.

Red17

yep, i believe that this 'backfiring' as described is actually 'over-run'. I think it has something to do with the fluid (exhaust) flow through a pipe and the effect of massive changes in flow velocity as you change gears (i.e very fast gas flow to much slower)... sort of a reverberation within the pipe. This happens more with aftermarket exhausts due to the increased diameter resulting in a greater flow speed differential. Of course if your mixtures are rich then this will also cause exhaust noise as the unburnt fuel is ignited outside the combustion chamber.

This is only a guess, but i think it is reasonable given the aerodynamics i studied through my (unused) mechanical engineering degree... feel free to correct me if i'm wrong.

OK...youve given me some ideas...thanks.

Some great theories, and it's intriguing that others suffer the same problem.

It is actually a popping noise, rather than a backfire, still, it is a bit distressing. Is it damaging though ??

I do have an aftermarket exhaust...a Kakimoto NS309....but the problem has only recently started....possibly after I was stuffing around with the BOV tension.

I might try tightening up the BOV (an atmo) and see if that has any effect.

cheers Ozzy

same here ED!

The Skylines are known to run very rich. Up the boost and the ECU over compensates even more. Mine is starting to sound like a rally car on the up changes ( running 0.9 bar ).

Could be wrong but I definately though it was unburnt fuel from running too rich.

BUT it sounds COOL...RIGHT???

Maybe not 90% of your driving time tho, that'd be a little annoying! I can get mine to back fire any time usually, just nail it and the back off real quick, if no back fire, lightly tap the Loud Pedal and you should hear the fruits of your labour.

I think my plugs need replacing now, but that's OK...

Yeah its just a pop, not a huge backfire... yeah its cool, there is one corner on the way home if I get the green light I can wind it down from 80km/hr to around 40km/hr and drop it into 2nd and I got a nice pop out the back... I suppose if I had a dump+front pipe and no cat I'd get flamage :P

I bet if you put the standard BOV back on you wouldn't hear a sound...

Yes the ECU expects an extra burst of air from the plumb back which is expelled from the intake system, so it compensates for this by adding fuel. This also solves the mystery of why some after market BOV make your car stall (over fuel).

A mate of mine solved this by installing an AVO atmospheric/plumb back BOV (all in one).

But if you don't mind the sound, forget about it, it's doing any harm.

Have Fun.

Yesiree, it is mine.....thanks....I think it looks good too. It came from Japan like that....I believe it is a standard factory R33 GTR bar.....Its good in several ways....you can remove the bottom lip when its been scratched to hell and repaint it off the car....(the beast has Tein's all round and is set on the stops)....it also allows you an absolute shirtload of room for a FMIC....which will come when the MRS lets me spend some more (of my) money.

cheers Ozzy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...