Jump to content
SAU Community

Recommended Posts

To gauge the general consensus as to how my engine came to be in its current condition I thought I would ask SAU'ers their opinions. Give me your ideas as to the causes of what you see below. At the least, I might get a laugh out of it as that is all I can do at this stage.

Charlie.

post-4183-1138797324.jpg

post-4183-1138797911.jpg

post-4183-1138798064.jpg

Link to comment
https://www.sau.com.au/forums/topic/104196-tell-me-what-happened-to-my-engine/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

hard to say with the pics supplied if you have some more you could show of the destruction thatd be handy, and what did the other pistons look like etc?

and could you describe what you where doing at the time, was it making nosie leading up to its death, stuff like that

I wasn't driving and unfortuntely I wasn't anywhere near the car. They are the only pics I have. Cyl #1 bearings are down to the copper, that piston & rod is from # 6. The rest appear to be fine.

The clues are in the LH photo. The question is whether the debris/parts were found 'as shown' (ie with bolts separated as shown), and if that is the case, how is it that one bolt appears remarkably undamaged given the extensive damage to the conrod ??.

bearings down to copper suggest oil starvation then had the bearing seize, which forced the piston onto the side of the bore, jamming it there which forced the bolts out as the crank continued round..

my opinoin is either

1) As stated by craved oil starvation caused a bearing to lockup

2) Rod bolts were not torqued to the correct specs meaning one of the bolts came loose causing the rod to jam on the crank as the crank turned it wedged the rod/piston against the bore and with no where to go the rod bent and i think it is safe to assume that the broken part of the conrods bigend is the part that put the hole in the block.

Just my 2 cents

my opinoin is either

1) As stated by craved oil starvation caused a bearing to lockup

2) Rod bolts were not torqued to the correct specs meaning one of the bolts came loose causing the rod to jam on the crank as the crank turned it wedged the rod/piston against the bore and with no where to go the rod bent and i think it is safe to assume that the broken part of the conrods bigend is the part that put the hole in the block.

Just my 2 cents

i would have to agree with you on the 2nd one.

in that one pic it looks like there is a WHOLE rod bolt, so my guess is that something was not torqued down on that rod and when it loosened it ate the bearing and killed the rod.

that sucks a large one there mate, i would consult the engine builder and raise hell as that (to me atleast) looks like some one didnt check the torque specs on the rod bolts.

were those tomei rods?

I know it doesnt help, but this is why I have a strong belief that workshops have their limitations since most of the specalist work engines/gearbox rebuilds is handled by a third party. I personally prefer to use

1) Dedicated engine builder

2) Good mechanic familiar with the car

3) Good tuner whether independant or a workshop

In the pic on the left there is a bolt there that has been snapped, is the other half still in the big end cap? if so then theres your answer, the bolt broke opening up the bearings crankshaft came out of the conrod piston stopped then when crank came around again smashed into hanging conrod and bearing and hey presto! total utter CHAOS!

BTW assuming you are going to follow this up with the builder, you need to get the motor and all bits back asap and take them to a 3rd party specialist, there are companies around who specialise in investigating and acting as specialist witnesses if it comes to that

Well maybe the engine was just on its way out due to bearing wear, it is very hard to diagnose a failure like this on an engine which has been in use for some time.

NXTIME when you say you had a problem with the engine what was the problem? and what did the workshop do to rectify this?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...