Jump to content
SAU Community

Recommended Posts

No you won't. If it's the pod filter sounds that comes out when you release the throttle, that's the air venting from the stock blow of valve of which your n/a car won't have.

However, putting a pod filter on your n/a car should give you a nice sucking noise when you accelerate as the air whooshes through. The stock skyline airboxes are muffled, thus the reason you hear no sound from them.

If you want to hear a cool noise, take the lid off your airbox and do a lap around the block. Of course, leave the filter there but without the lid you should be able to hear the sucking noise. A pod filter will sound similar to this but much better.

Yeeha!

mine makes more of a masshoosszzzleeeppphhhtttfffhhggghhmmmmmmzzzzaaappp

you wish! i've seen your car bro and i swear it wasnt makin that noise when i dun seen it. stop makin shit up man. we both no it wz moor of a whoopwhoopwhoopptshhhhhh noise.

yes i know the sound your talking about also. one of the main reasons i bought a line was because the way they sound! even without an exhaust system. My series 2 33 gts-t only has a pod, and dam does it make a sexy hiss to scream sound when it climbs the revs. thinking of not installing an ehaust and leaving it be, some people call it the python :)

My mates r33 gtst didnt make the sound - put a pod filter on and it did.

my my98 wrx didnt make the sound - put a pod filter on and it did (stock other then this too)... as everyone else said.. it is just the pod, some blow off valves will give that noise too... a NA car will never sound like the turbo cars do (by just putting a pod on).

Dayne

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...