Jump to content
SAU Community

Recommended Posts

Just to let you guys know we picked up 40awkw on a 420awkw WRX in changine from 99 coil pack system running dumb ignitor with autronic dwell control using a 0.6mm gap to using full CDI igntion with proper coils and 0.9mm gap!!! Mind you it was braking down slightly before hand but the results were throughout the rev range.

hahaha.. that's what my R31 was like. You could even give it a polish and it would drive like a new car for 2 days. I think it was just my mind playing tricks on me :)

A bit like the do an oil change and it feels faster or smoother syndrome. :)

A bit like the do an oil change and it feels faster or smoother syndrome. :)

no way .. that works

i lose 50km a tank if i use the oil too long in my run around lancer Gli

change it and i instantly (next tank) get that 50km back

  • 2 weeks later...

Hey just out of curiousity, my tuner replaced my copper plugs with Iridium NGKs and all of a sudden i'm getting huge misfire around 5000rpm (at 0.8 bar) Nothing else has been changed as far as I know. Does it sound like they're 1.1mm gapped and I just need to change it to 0.8?

Gread thread by the way, very helpful to a newbie like myself.

Edited by Lithius
Hey just out of curiousity, my tuner replaced my copper plugs with Iridium NGKs and all of a sudden i'm getting huge misfire around 5000rpm (at 0.8 bar) Nothing else has been changed as far as I know. Does it sound like they're 1.1mm gapped and I just need to change it to 0.8?

Gread thread by the way, very helpful to a newbie like myself.

crazy dude why pay to retune a car that already had a $500 tune?

secondly GTT's hate iridiums thats why the car had coppers in it.

put coppers back in and gap to .8

  • 1 month later...
  • 3 months later...

Im using NGK IRIDIUM BKR5EIX-11, so i guess that means that they are heat range 5 and have a gap of 1.1mm, is this heat range ok (mods at the moment are hks catback and decat pipe)???

The reason i ask is because at the moment my car seems to hesitate randomly down low sometimes (usualy in 2nd and 3rd gear) and feels a bit sluggish down low aswell (goes fine at 100% throttle in every gear). And sometimes has a very quiet pop out the exhaust.

Do you reccomend i keep the plugs i am using now and gap them down to 0.8mm? or go and buy a different heat range plug and gap that down to 0.8mm??

I would really appreciate some help as its getting a bit frustrating lol

By the way someone should sticky this thread!! it will come in handy for alot of people im sure :(

Cheers

Im using NGK IRIDIUM BKR5EIX-11, so i guess that means that they are heat range 5 and have a gap of 1.1mm, is this heat range ok (mods at the moment are hks catback and decat pipe)???

The reason i ask is because at the moment my car seems to hesitate randomly down low sometimes (usualy in 2nd and 3rd gear) and feels a bit sluggish down low aswell (goes fine at 100% throttle in every gear). And sometimes has a very quiet pop out the exhaust.

Do you reccomend i keep the plugs i am using now and gap them down to 0.8mm? or go and buy a different heat range plug and gap that down to 0.8mm??

I would really appreciate some help as its getting a bit frustrating lol

By the way someone should sticky this thread!! it will come in handy for alot of people im sure :(

Cheers

How does your plugs look now? If it looks white like the picture in the link, then you have overheated plugs. NGK

If not, then gap down by tapping lightly to 0.9mm or lower (use feeler gauge to measure). See if it helps. Iridium plugs normally perform better then normal copper plugs due to hotter kernel flame & lower voltage required to jump the gap.

Edited by Trex101
How does your plugs look now? If it looks white like the picture in the link, then you have overheated plugs. NGK

If not, then gap down by tapping lightly to 0.9mm or lower (use feeler gauge to measure). See if it helps. Iridium plugs normally perform better then normal copper plugs due to hotter kernel flame & lower voltage required to jump the gap.

Cheers for the reply mate, i will check if the plugs are overheating when i have some spare time

It says on the iridium box "Do not adjust spark gap due to extremly fine center electrode", i just tried gapping down a used set of iridium spark plugs and when you insert the feeler gauge (after they have been gapped down) to check if the gap is correct then remove the feeler gauge it bends the center electrode and because its so fine the electrode sometimes snapps off!

So i dont exactly want to risk trying to gap down $80 worth of ngk iridium plugs to find that the electrodes snapp off.

Edited by nizmo_freek
Cheers for the reply mate, i will check if the plugs are overheating when i have some spare time

It says on the iridium box "Do not adjust spark gap due to extremly fine center electrode", i just tried gapping down a used set of iridium spark plugs and when you insert the feeler gauge (after they have been gapped down) to check if the gap is correct then remove the feeler gauge it bends the center electrode and because its so fine the electrode sometimes snapps off!

So i dont exactly want to risk trying to gap down $80 worth of ngk iridium plugs to find that the electrodes snapp off.

The correct way to gap a iridium.

Iridium gapping

I have a few questions that have not been covered yet.

Have a look at the plugs pictured below and you will notice that the plugs are different lengths from the plug seat (top ot the thread where they sit in the head) to the top of the pin that the coilpack connects to.

100_1301.jpg

The height difference is approx 5mm.

The plugs that came in my R32 were BPR5EIX and were longer than the BCPR6EY-11. I gapped them down to 0.8.

The first thing I noticed is when you sit the coil on the new plug it only just compresses the spring at the top of the coil it is not a tight fit.

With the older plugs the top of the coil would actually click in and hold the top of plug like an octopus tenticle.

I have also tried BCPR6E and have found the same thing.

I have chronic missfire if I run over 14psi even with the BCPR6E. and believe it or not with the BPR5EIX-11 platinum plug gapped at 1.1 I have no miss untill 16psi.

does the plug height make a difference and has anyone else noticed this?

I have splitfires coming very soon and will not change the plugs as they are only 2000k's old and are BCPR6E and see if the coils alone fix the miss.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...