Jump to content
SAU Community

Recommended Turbo Installer In Melbourne


Recommended Posts

get a gasket kit and do it yourself, seriosly, its like 4 bolts, a few pipes and oil fitting, if you dont have a dump, it will be fun driving it to a zorst shop

you will save like $1500 and make sure that you know exactly whats done

youll probly need to take the manifold off too and replace allthe studs but thats not that hard

Assuming you have a garage and the right tools ;)

Al i dont have a garage, i have a carport and i've changed my turbo once and my brothers once. It really isnt that hard, An rb turbo swap could almost be done in a day. And as for getting tools, i'm sure someone has a basic socket set which is all you really need, maybe an open ended spanner or two.

You can see what needs to be taken off on an rb so the swap is stright foward.

beno owns race pace. and benny used to work for chasers, now benny  has started his own garage up with another person, which is called high end racing.

Is Chasers still around? I've only went passed there (Dynon Rd) a few times a while ago but didnt notice if the workshop still there.

Is Chasers still around? I've only went passed there (Dynon Rd) a few times a while ago but didnt notice if the workshop still there.

ye they are still there..told them hundreds of times to put a big sign up..but still shouldn't be hard to find the joint coz they always got heaps of nice cars parked at the front

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...