Jump to content
SAU Community

Recommended Posts

i didnt think they were legal but reading the new motor magazine states that they are, definatley gonna find out for sure since i have them and wanna know 100%... mine a so secure feels so safe, i guess if they rattle then they would be defected for but secure ones i cant see whats wrong

i cant see why the flush mounted ones would be additional hazard to pedestrians... maybe the ones with the wire over the front or the ones that stick up... maybe try checking in your state... like everything else the laws owuld vary from state to state... just ring you local rta they will tell you...

I was in that position with a Bluebird that had a much modified rad support panel (foreigh R32 rad and hooge IC) . The answer was to fit a plunger (or as suggested to me dog cock !) style catch from a Datsun 1600 . It works well but the fabrication to fit it to the bonnet is involved and may damage its paintwork .

Cheers A .

They are Legal in Canada :P

and for the ones that rattle.... they were probably cheep ones... get them from a good Canadian or Japanese manufacturer :P

Edited by James Mramor

I thought they were illegal for pedestrian safety too.

Anywya, for pins that rattle they aren't tight enough. Either crank the pins down or add to the support between the bonnet and the chasis

  • 7 months later...

I have the larger ones on mine, with a latch, illegal in the ACT, wouldn't mind swapping them for the smaller ones. or putting blanks on the bonnet, as it looks bad atm with holes in the bonnet :O, anyone know if thats legal?

Can't comment on the legality of "bonnet pins" however i would see a car manufactures badge that protrudes the bonnet to be more of a pedestrian risk then a bonnet pin, but this is common sence therefore, it's probably the case that the pins are illegal in NSW. If they are, i'd just go flush mounted ones like someone already sujested.

I think it depends on the type of bonnet pin some cars come with them standard one that springs to mind are the old gt falcons which had flush fitting bonnet pins no protrusion above bonnet line so id say pins that protude above the bonnet line would become a problem for pedestrians i.e cause more damage to them .So if fitting bonnet pins try for something flush mounting

Cheers Peter

  • 2 weeks later...

bonnets are meant to crumple when you hit a pedestrian or crash, this makes it safer for you and the pedestrian. if the bonnet doesnt crumple it can go straight through your windscreen and take your head off. bonnet pins would probably be illegal because they'd prevent the bonnet crumpling properly.

This was argument a cop had with me regarding lifting the back of the bonnet up two inches for enhanced cooling away from the rear internal clips, but I cant see how pins would be a problem as they would retain the bonnet to the frame better.

The pedestrian damage issue would be the main reason, if in fact it is illegal.

Then again if it's a :-

Skyline = Illegal

Falcodore = Illegal

EuroWeapon =Legal :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...