Jump to content
SAU Community

Recommended Posts

i didnt think they were legal but reading the new motor magazine states that they are, definatley gonna find out for sure since i have them and wanna know 100%... mine a so secure feels so safe, i guess if they rattle then they would be defected for but secure ones i cant see whats wrong

i cant see why the flush mounted ones would be additional hazard to pedestrians... maybe the ones with the wire over the front or the ones that stick up... maybe try checking in your state... like everything else the laws owuld vary from state to state... just ring you local rta they will tell you...

I was in that position with a Bluebird that had a much modified rad support panel (foreigh R32 rad and hooge IC) . The answer was to fit a plunger (or as suggested to me dog cock !) style catch from a Datsun 1600 . It works well but the fabrication to fit it to the bonnet is involved and may damage its paintwork .

Cheers A .

They are Legal in Canada :P

and for the ones that rattle.... they were probably cheep ones... get them from a good Canadian or Japanese manufacturer :P

Edited by James Mramor

I thought they were illegal for pedestrian safety too.

Anywya, for pins that rattle they aren't tight enough. Either crank the pins down or add to the support between the bonnet and the chasis

  • 7 months later...

I have the larger ones on mine, with a latch, illegal in the ACT, wouldn't mind swapping them for the smaller ones. or putting blanks on the bonnet, as it looks bad atm with holes in the bonnet :O, anyone know if thats legal?

Can't comment on the legality of "bonnet pins" however i would see a car manufactures badge that protrudes the bonnet to be more of a pedestrian risk then a bonnet pin, but this is common sence therefore, it's probably the case that the pins are illegal in NSW. If they are, i'd just go flush mounted ones like someone already sujested.

I think it depends on the type of bonnet pin some cars come with them standard one that springs to mind are the old gt falcons which had flush fitting bonnet pins no protrusion above bonnet line so id say pins that protude above the bonnet line would become a problem for pedestrians i.e cause more damage to them .So if fitting bonnet pins try for something flush mounting

Cheers Peter

  • 2 weeks later...

bonnets are meant to crumple when you hit a pedestrian or crash, this makes it safer for you and the pedestrian. if the bonnet doesnt crumple it can go straight through your windscreen and take your head off. bonnet pins would probably be illegal because they'd prevent the bonnet crumpling properly.

This was argument a cop had with me regarding lifting the back of the bonnet up two inches for enhanced cooling away from the rear internal clips, but I cant see how pins would be a problem as they would retain the bonnet to the frame better.

The pedestrian damage issue would be the main reason, if in fact it is illegal.

Then again if it's a :-

Skyline = Illegal

Falcodore = Illegal

EuroWeapon =Legal :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...