Jump to content
SAU Community

Recommended Posts

so im told. AFM's r inacurate :) they measure how much air goes thru the intake of the turbos. wher as the Map sensors r in throttle and measure the boosted air which is more consistant.

aint that right?

ok correct some of us mislead ppl. why r afms so much better than a Map read system?

Edited by markimak

AFM measures the volume of air going into the engine, a map sensor guesses the volume by comparing revs, pressure, and throttle position.

The volume of air is what realy counts, as it's the amount of air getting into the engine, not what pressure is behind it that gives you power. and say you hit full boost at ~ 4000rpm, the map sensor is going to read the same manifold pressure right till redline, and will have to guess the load axis for the ecu.

i have no idea if that makes any sence. But do a search, it has been covered heaps.

sounds like it could be the knock sensor, nissan sesnors are crap! i had to replace my afm, o2 sensor and now my knock sensor in my 180.

also make sure you do not drive your car or leave it idling if the oil has no presure otherwise you will need new bearings whcih means a rebuild.

the MAP sensor is direct manifold air pressure. not a vaccumed pressure like afm.

ok, firstly i have nfi what 'vacuumed pressure' is. pressure is a force pusing on something, vacuum is the pretty much the opposite. regardless, it's wrong. The mass air flow meters used in a GTR use a hotwire element that converts a change in temp to a voltage sigal which give an accurate measure of airflow. it has nothing to do with pressure as such. a Manifold Absolute Pressure sensor measure the pressure in the manifold (not in the throttle as you mentioned, after the throttle(s)). this is ok, but it's no where near as accurate as a hotwire type AFM. do a search in this forum as it's been covered many times before and you will learn a little about the differences.

Hey dude i know how ya feel mine is doin the same only it fluctuates all over the place one minute it will drivin along fine then to pull up it doesnt want to idle. At first i thought afm's straight up but i pulled them off cleaned them out an it run a little better for awhile. So i had them tested an they checked out fine. I had a diagnostic check done on the car an in my fuel mapping area i was over fuelling pretty heavy in the high rev range so we pulled fuel out of that area but unforntunatel the problem still lingers

think this is a problem with alot of GTR's the amount of other GTR's that have done the same thing. hmm. mine hasnt acted up for over a week..

wat i did.

remove top AFM

clean afm with carby spray.

took off the connecting. cut old one off made up new connectors.

disassembled the afm cleaned connections. its only 4 screws.

connected all up.

Made heat shield for AFM plug with alfoil (looks dodgy, i did this to protect the heat shrink on the connector plug i made up.)

ran its so far so good.

noticed it aint as punchy as it was before. been meaning to reset ECU.

i was reluctant to snip up my harness. but had a spare plug off another GTR and used it as a reference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...