Jump to content
SAU Community

Recommended Posts

Im thinkin about buyin one as well..

After a gd wash, if i go park the car in the garage, there wil be crap from top of the roof that falls down n pisses me off..

covers range from 20-80bucks from super cheap!!

The only down side is, you gotta take it off each time you want to get into the car or work on it/put it back on..

I guess to protect your car, you should buy one!!

or those portable carport things..

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2059024
Share on other sites

I think it's a good idea. At my house the garage is pretty much taken up by my dad's, mum's and bro's cars, so my car has no choice but to sit out in the front yard under the electricity wire where birds sit and shit on everything underneath it (should see some of the shit that comes out of these birds). Anyway, too save money and pain invest in one coz leaves and dust is not as bad a bird shit.

Prices do vary for em, but there are ones that have a special material that let the car breathe on hotter days etc so u dont get too much condensation inside the cover. I guess it's really dependant on how much u wanna spend.

:P:D

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2059236
Share on other sites

A major consideration when buying a car cover, is where you park the car.

If you park in a garage as siddr20 does, then it should be fine, provided that the car is perfectly clean every time the cover is put on.

If the car isn't clean, you're dragging dust and grit across the car while trying to fit the cover.

If your car lives out in the open, take pressure points into consideration...

Unless it's a custom made cover, it won't fit like a glove.

Generic car covers are floppy, and will flap around in the wind.

This flapping eventually wears at the paintwork.

Dust and bird poo are temporary mess which can be washed off.

....unlike the damage which can be caused by a poorly fitting car cover flapping on the paintwork for 16 hours a day.

Some of the high-end generic covers will have fluffy stuff inside them, this does bugger all apart from cause bits of leaves, small sticks and other debris which get blown up off the ground to get stuck in the fluffy stuff, which damages the paintwork faster with each "FLAP FLAP FLAP!"

Take a look at some of the portable car ports.

They may cost more than a car cover, but they cost less than a respray. :D

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2059378
Share on other sites

would any one be concerned about condensation being trapped between the cover and the paint work? after a while it may cause the car to rust or is just me being paranoid? that the second reason i dont use a car cover first being the whole scratched paint thing.

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2060095
Share on other sites

dad and i went halves in a car cover cause we share the garage so when mine is out side - i use the car cover - as its for a large car, you havre to use the straps underneath - otherwise big wind blows it off (which i found out..:D)

they keep the dew off the car and leaves and crap outta the way - very good if you dont have a garage

:D

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2060211
Share on other sites

dad and i went halves in a car cover cause we share the garage so when mine is out side - i use the car cover - as its for a large car, you havre to use the straps underneath - otherwise big wind blows it off (which i found out..:D)

they keep the dew off the car and leaves and crap outta the way - very good if you dont have a garage

:D

So you had no issues with the car cover at all?

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2060215
Share on other sites

none at all :D

i guess just make sure the car is clean before you cover it up.

dont go the cheap brands either - i had one of them for my old VT commodore and the elastic just lost its elastisty, didnt last long.

Think we paid 80 odd bucks at kmart/auto1 for this one and extremely happy with it :D

Link to comment
https://www.sau.com.au/forums/topic/111641-car-covers/#findComment-2060301
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...