Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

so what should i do, i'v taken the car back numerous times and it's always the same result, all that happens when i take it back is the tuner just keeps lowering the timing, to me it seems like he just can't be bothered

I might as well get the stock ecu put back in, cause thats what it feels like

Edited by Hulk1010
It really depends where it is knocking.

If it's on over run then not a major concern, or if you are bouncing off the limiter then it isn't uncommon as the pfc cuts fuel creating a lean condition

Fuel cuts aren't a lean condition as all the injectors are shut off. Knocking on the rev limiter is usually from crackshaft harmonics due to the massive rotational decelleration. Find out when the knock occurs and we might be able to help you out more.

Edited by rob82

thanks for the replys

I'ts always before the limiter, at random times, I might give it a boot from 2nd, 3rd, 4th etc and end up getting a high reading, could it be the knock sensor?

a week back i gave it a boot from second and then checked the knock level reading and it read 111, the RPM was 5500

thanks for the replys

I'ts always before the limiter, at random times, I might give it a boot from 2nd, 3rd, 4th etc and end up getting a high reading, could it be the knock sensor?

a week back i gave it a boot from second and then checked the knock level reading and it read 111, the RPM was 5500

By that knock level you should actually start to hear it through the fire wall. Is it a temperature based problem ie does it do it at night on the highway or slow cruising around town in the heat of the day?? If you pull 2 deg out globally does it stll do it??

By that knock level you should actually start to hear it through the fire wall. Is it a temperature based problem ie does it do it at night on the highway or slow cruising around town in the heat of the day?? If you pull 2 deg out globally does it stll do it??

OK - I kind of have this problem too – but not as bad

I have an R32 GTR with Weisco forged pistons - and my knock reading creeps up to the high 50s from time to time. I have also seen bursts up into the 70s but only if I'm using bad fuel.

I have had my engine checked by 3 different tuners - all using head phones to listen for knock - and they all confirm that my engine is NOT knocking

Under the settings menu on your PFC you add advance / retard timing and increase the injector duty cycle across the entire rev range – or 'globally'

I tried taking timing out in steps. I stepped up from -2 / -4 / -8 degrees - and it made no difference to the readings.

I then added more fuel 'globally' - still no difference

I then did some tweaking to both at the same time – still got the same readings (shrugs)

So - I figure I either have a dodgy knock sensor - or just a noisy engine :)

or possibly both

The knock reading can be misleading as ive seen many cars with high readings with no det at all.One GTS read a count of 93 no matter what you did, we even backed the CAS off asd far as it could go and retarded timing with the PFC with no change,even changing the knock sensors did nothing.Use the reading as a guide only but its no where near perfect so us other means as a back up if your not sure.

A maximum power tune will give readings in the 50s also,this is why i like to use other tools for det detection on the dyno on hi powered cars.

Does it do it all the the time?

Every now and then I'll get really high readings,spoke to the tuner and he mentioned it could be the fuel pump.

I've just replaced it and its still playing funny buggers, highest knock of 120 when overtaking in fifth gear with less than 3 qtr throttle.

All other times sits on mid to low 30's!

same boat **raises hand.

Mine has hit a max of 84, but after a bit of driving in low and high revs the knocking is down to lower than ~30. Is this a problem at all?. If I am driving with no hard boosting the knocking is lower than 20....

Also have been told to watch for blowing smoke.

White = water

Brownish = fuel

Black = oil

is that right?

I've put about 6,000km on my GTR in the past 4mths driving in conditions from 5c-44c on 0.8-1.4bar and never have I seen my knock level go above 32.

Maybe it is time for you to find a different tuner Hulk.

I have the same problem with my gtstr33. it spikes upwards of 120 with the aircon on, and up around 50-60 with aircon off. It happens at around 4500-5000 rpm.

I have my map locked so i cant take out any timing to do some fault finding. This is quite annoying seeing the engine check light flash rapidly at me. I hate the thought of slowly killing my engine.

I had mine tuned at one of the best tuners in sydney and it was not detonating on the dyno. I even took it back for them to play with and they did take some timing out. I am wondering if its possible for the car to be using different load points under wot on the dyno to wot on the road. In this case that part of the map may not be tuned????

Does any one else notice a rise in knock if the aircon is on???

^ The engine is working harder with the aircon on... so its gonna show up.

Take it back to this "one of the best tuners" and tell them its still happening. Sacrafice a little bit of power for the overall health of your engine...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
×
×
  • Create New...