Jump to content
SAU Community

Recommended Posts

My target is 280rwkw from my R34 GTT. Turbo that will be used is GT3071R (90T) along with all other supporting mods including power fc and tomei cams. My question is if the bosch 040 will be sufficient enough to supply the fuel through the 480cc nismo injectors? If not will i have to upgrade to the external 044 ( dont want the nosie) or can i just get a pressure regulator?

Link to comment
https://www.sau.com.au/forums/topic/118346-power-goal-280rwkw-from-a-neo/
Share on other sites

thats a mean looking car you have there hyper!!! wot mods and turbo u runing?

Thanks Mate :thumbsup:

It's a GT3540R ext gate with the usual supporting mods.

Cams

Injectors

Fuel pressure reg

FMIC

fuel pump

Power fc

Cheers,

JB

im a great fan of search so dug up this thread

i want to build a fuel system capable of 350+kws at the wheels

the car will be used for burnouts and the occasional bit of drag racing

will i need to run a rb20det fuel pump feeding into a surge tank then something like an 044 from there or will the 040 in tank suffice. i would also hard wire the feeder pump. what size lines would i also need?

ideally id like to keep the boot room but dont want to run out of fuel.

My target is 280rwkw from my R34 GTT. Turbo that will be used is GT3071R (90T) along with all other supporting mods including power fc and tomei cams. My question is if the bosch 040 will be sufficient enough to supply the fuel through the 480cc nismo injectors? If not will i have to upgrade to the external 044 ( dont want the nosie) or can i just get a pressure regulator?

would a direct replacement nismo or tomei for a gtst r33 support 280rwkw or even a nismo or tomie for a gtr into a gtst?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...