Jump to content
SAU Community

Recommended Posts

My target is 280rwkw from my R34 GTT. Turbo that will be used is GT3071R (90T) along with all other supporting mods including power fc and tomei cams. My question is if the bosch 040 will be sufficient enough to supply the fuel through the 480cc nismo injectors? If not will i have to upgrade to the external 044 ( dont want the nosie) or can i just get a pressure regulator?

Link to comment
https://www.sau.com.au/forums/topic/118346-power-goal-280rwkw-from-a-neo/
Share on other sites

thats a mean looking car you have there hyper!!! wot mods and turbo u runing?

Thanks Mate :thumbsup:

It's a GT3540R ext gate with the usual supporting mods.

Cams

Injectors

Fuel pressure reg

FMIC

fuel pump

Power fc

Cheers,

JB

im a great fan of search so dug up this thread

i want to build a fuel system capable of 350+kws at the wheels

the car will be used for burnouts and the occasional bit of drag racing

will i need to run a rb20det fuel pump feeding into a surge tank then something like an 044 from there or will the 040 in tank suffice. i would also hard wire the feeder pump. what size lines would i also need?

ideally id like to keep the boot room but dont want to run out of fuel.

My target is 280rwkw from my R34 GTT. Turbo that will be used is GT3071R (90T) along with all other supporting mods including power fc and tomei cams. My question is if the bosch 040 will be sufficient enough to supply the fuel through the 480cc nismo injectors? If not will i have to upgrade to the external 044 ( dont want the nosie) or can i just get a pressure regulator?

would a direct replacement nismo or tomei for a gtst r33 support 280rwkw or even a nismo or tomie for a gtr into a gtst?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...