Jump to content
SAU Community

Recommended Posts

Hello ladies,

Question for the day,

Looking at getting some HKS Cams/cam gears - should I do it with my set up

Hopefully i just picked up a HKS Low mount and trust ext. gate to go with my Biago turbo I am getting through Murnane cant remember much about the turbo exactly was initially going the smaller internally gated one but now with the new manifold I will be more than likely doing what slide was selling as a Biago T40 if you can remember what that was.

Fairly decent sized turbo so I’m guessing there will be a little lag to contend with

Current state: PFC, FMIC, full Exhaust,

Adding: Turbo, Manifold, Gate, 740cc Injectors, 040 Pump,

Considering: Cams / Cam Gears

If need be I will call murnane to get the details of the turbo but as far as I know he basicly will customise the turbo to application

And im asking in here cause the forced induction forum is full of wankers and is too messy to navigate/get an answer and i have come to value the oppinions of the regulars of the wasteland

Cheers,

Dan

sarp fool

well basically with the 25 head u dont have that greater pick of cam's, as the std hydraulic lifter setup can only go so far in lift. (9.XXmm i think it is)

saying that, i'd prolly go with something around the 250-260deg and 8.5-9.15mm lift.

looking on greenline, tomei only do a poncam of 256deg duration & 8.50mm lift. hks do 256deg 8.8lift or a 260deg 9.0lift.

depends how big that turbo is, id go the bigger of the cams

however, if u were going take the head off and get it refreshed, u can easily get it converted to a solid lifter setup, then u can run a gtr cam, which u'd have a hell of a lot more option with cam selection

sarp fool

well basically with the 25 head u dont have that greater pick of cam's, as the std hydraulic lifter setup can only go so far in lift. (9.XXmm i think it is)

saying that, i'd prolly go with something around the 250-260deg and 8.5-9.15mm lift.

looking on greenline, tomei only do a poncam of 256deg duration & 8.50mm lift. hks do 256deg 8.8lift or a 260deg 9.0lift.

depends how big that turbo is, id go the bigger of the cams

however, if u were going take the head off and get it refreshed, u can easily get it converted to a solid lifter setup, then u can run a gtr cam, which u'd have a hell of a lot more option with cam selection

Weak, I had 272's.

Speaking of which they just came out, some soild lifters went in and bigger cams again. f**k I should buy that car back lol.

shotgun (if they are suitable) :P

this is what i have sitting in my nengun shopping cart:

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 INLET, Duration 256. Lift 8.8mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN172 - AU $ 378.77

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 EXHAUST, Duration 264. Lift 9.0mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN175AU $ 378.77

Would that be on the money?

also will it sound cool? :)

whats Noel got?

also I was gonna go with HKS injectors just to be a complete brand fag, I have not heard of many people running them any opinions on them? i seem to mainly hear people useing nismo/sard

^^^^^^^^Ok its on the 26th next weekend, its a show, shine and swap meet. Its held at Pine Rivers Park at Strathpine. I think thats on the main drag going out to Petrie. Might be Gympie Rd.

It was posted here but it was closed for some unknown reason.

That little tree symbol at the centre of the map is what Whereis gave me as Pine rivers park, what time does it start?

post-17300-1187340023_thumb.jpg

That little tree symbol at the centre of the map is what Whereis gave me as Pine rivers park, what time does it start?

Thats farkin Jambo weekend dude. Who's the klutz that lined it up against that?

That little tree symbol at the centre of the map is what Whereis gave me as Pine rivers park, what time does it start?

Not sure between 9-11am. I think you would be safe to see a few things.

shotgun (if they are suitable) :D

this is what i have sitting in my nengun shopping cart:

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 INLET, Duration 256. Lift 8.8mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN172 - AU $ 378.77

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 EXHAUST, Duration 264. Lift 9.0mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN175AU $ 378.77

Would that be on the money?

also will it sound cool? :P

whats Noel got?

also I was gonna go with HKS injectors just to be a complete brand fag, I have not heard of many people running them any opinions on them? i seem to mainly hear people useing nismo/sard

Fark yeah that is cheap for HKS cams, whats the delivery fee around $800 to ur door :) .

those prices are delivered!!! not bad eh

this is my shopping cart at the moment:

HKS - Cam Pulley - Duralumin

Nissan RB26DETT/RB25DE(T) All Duralum / Slide, For inlet side (except for NVCS engine).

22004-AN001 AU $ 148.87

HKS - Cam Pulley - Duralumin

Nissan RB26DETT/RB25DE(T)/ All Duralum Slide, For exhaust side

22004-AN002 AU $ 148.87

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 INLET, Duration 256. Lift 8.8mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN172 AU $ 378.77

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 EXHAUST, Duration 264. Lift 9.0mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN175 AU $ 378.77

HKS - Fine Tune Timing Belt

Nissan RB20DET, RB25DET, RB26DETT

24999-AN001 AU $ 139.55

HKS - Fuel Injectors

HKS 740cc Side Fed injectors ( Red )

1402-RN009 AU $ 793.53

Splitfire - Super Direct Di ignition system

Nissan - Skyline - ECR33 - Series 1 - 8/93-1/95

SF-DIS-001 AU $ 471.41

Order Total AU $ 2,459.76

Delivered to Brisbane 4127

now just to roll a couple of granny's next thursday and I will be set

those prices are delivered!!! not bad eh

this is my shopping cart at the moment:

HKS - Cam Pulley - Duralumin

Nissan RB26DETT/RB25DE(T) All Duralum / Slide, For inlet side (except for NVCS engine).

22004-AN001 AU $ 148.87

HKS - Cam Pulley - Duralumin

Nissan RB26DETT/RB25DE(T)/ All Duralum Slide, For exhaust side

22004-AN002 AU $ 148.87

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 INLET, Duration 256. Lift 8.8mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN172 AU $ 378.77

HKS - Camshafts - Nissan

Nissan ECR33 RB25DET -97/8 EXHAUST, Duration 264. Lift 9.0mm (For NVCS engines, Not suitable for NEO Straight 6)

2202-RN175 AU $ 378.77

HKS - Fine Tune Timing Belt

Nissan RB20DET, RB25DET, RB26DETT

24999-AN001 AU $ 139.55

HKS - Fuel Injectors

HKS 740cc Side Fed injectors ( Red )

1402-RN009 AU $ 793.53

Splitfire - Super Direct Di ignition system

Nissan - Skyline - ECR33 - Series 1 - 8/93-1/95

SF-DIS-001 AU $ 471.41

Order Total AU $ 2,459.76

Delivered to Brisbane 4127

now just to roll a couple of granny's next thursday and I will be set

Fark yeah thats a nice list :D . I am lining up a set of Tomei cams but i might look at the HKS as they are only a little dearer but they have a better name, i spose you get what you pay for.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...