Jump to content
SAU Community

Recommended Posts

Just spent 5hrs washing, claying, polishing and waxing car.

Not happy with the autoglym super resin polish. Didnt cut enough. Need to use a stronger cutting compound to restore my paint.. hehe

Too tired to get proper pictures, maybe tomorrow

Mothers Clay bar

Autoglym super resin polish (waste of $30 -_-)

Mothers PowerWax

img1709mediumau0.jpg

img1701mediumce2.jpg

img1705mediumey9.jpg

Phaw!!! Looks mint! i wouldnt change a thing

Thanks mate. It's like a brand new car. Less than 60000k's with full service history, and less than 20000k's since 1996.

Not really planning on changing anything which is damn hard when there's a GTR in the garage :-)

Maybe the wheels, and I'm adding an oil cooler next week for protection, but that'll be it i think :down:

Just spent 5hrs washing, claying, polishing and waxing car.

Not happy with the autoglym super resin polish. Didnt cut enough. Need to use a stronger cutting compound to restore my paint.. hehe

Too tired to get proper pictures, maybe tomorrow

Mothers Clay bar

Autoglym super resin polish (waste of $30 -_-)

Mothers PowerWax

img1709mediumau0.jpg

img1701mediumce2.jpg

img1705mediumey9.jpg

Looks damn good in my books mate.

I have never really understood what the clay part does though.

Looks damn good in my books mate.

I have never really understood what the clay part does though.

Thanks for the comment :)

if you run your fingers over the paintwork on your car, you might feel a lot of bumps which you cant see.

Claybar is a peice of clay which you slide across the paint which sticks to these bumps(microscopic dirt/imperfections) and pulls them out of the paint. Leaving a real smooth paint afterward.

Rekin, looks tops mate :)

I can't see what you're worried about from those pics. Paint looks pretty good.

haha, wasnt too impressed over the autoglym super resin polish. $30 for 375ml's expected a real good cut.

Although reading some fine print on the internet, they say to do 2-3 coats of the polish to get a good result.

Although it be quite hard to squeeze 3 coats out of a 300ml bottle...

Just finished washing my car and decided to take a few shots. Should have taken it out of the shade

post-16070-1221704152_thumb.jpg

This is my new car that should be here in the next 2 months as long as everything goes to plan.

1993 R32 GTR vspec ;)

post-16070-1221704185_thumb.jpg

post-16070-1221704208_thumb.jpg

Edited by babyskyline

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...