Jump to content
SAU Community

Recommended Posts

  • 1 year later...
  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 10 months later...
  • 1 month later...

lol.

BTW does anyone know how to take the panel off an R32 without wrecking it? I have one of those light on ones, but it looks like it's stuck down with some sorta foam, wouldn't mind pulling it off and checking the electrical connections so I can have it lighting up properly!

  • 4 weeks later...

Skyline Light Up Tutorial

Doing this is at your OWN risk I take no responsibility for any damage or accidents which may occur throughout this tutorial, if you're unsure ASK, if you don't think you can do it DON'T

What You Will Need:

Dermal Tool (Rotary Tool)

Heavy Duty Dermal Cut Off Wheel

Dermal Sanding Band*

Rocker Switch* : If you want to turn it off and on

~ 14 High Intensity LED's ~$60+ from Jaycar or ~$20 from eBay, Check the light output rating

~6-14 Resistors: Pennies at Jaycar, You can use one resistor per LED or for every 2 (But if one burns out so will the other) Use THIS website to calculate the ohm's required for your array

Sheet of Experimenters Board: Try to get one that is long enough for the whole thing so you dont have to go through the hassel of putting them together

Some Wires: Try to get different colors for convince sake

Can of Paint: Match your color code (Recommend Autobarn Moorabbin, they can mix you up a can specific to your car and it's really useful for touch ups

Can of Lacquer*: Technically this isn't a must but it provides a nice shine & seal, also gives your that smooth feeling you have on your car

Painters Tape

Exacto Knife

th_1Garnish.jpgth_2Garnish.jpg

Alright we first start with your Skyline Garnish after taking it off of your car inspect i and make sure it's all nice and clean, you will notice some faded paint on the letters start by sanding them off to get the best light through

th_3RemoveTabs.jpg

Start by cutting the tabs off the back

th_4RemovePlastic.jpg

Now cut the entire plastic backing out, enough to expose all the letters; For my next project I'm going to try to cut a small hole instead and slide the entire board in but it's up to you

th_5RemovePlastic.jpgth_6RemovePlastic.jpg

This is what your Garnish should look like when you're finished

th_7SandEdges.jpg

You can sand down the edges if you really want to but in reality no one is going to see the back it's only for your own satisfaction

th_8PrepPaint.jpgth_9PrepPaint.jpg

Place painters tape across the lettering and run your fingers along the outside of the lettering it should tear the tape allowing you to just cover the individual letters

th_10Spray.jpgth_11Spray.jpg

After cleaning the Garnish again prep your area for painting (preferably outside) apply several even coats of paint (I did 5 if I recall correctly but it's based on how happy you are with it) allow at least 20 minutes between each coat (maybe less or more depending on the weather)

th_12Laquer.jpg

*REMOVE THE PAINTERS TAPE OFF THE LETTERING BEFORE APPLYING LACQUER* I forgot to remove the tape before applying the Lacquer which was a pretty stupid mistake and it ruins the finish, not by a lot but it's a lot of work to fix. After you completed your final coat allow drying for a few hours before applying Lacquer; this will seal the paint and give it a nice Glossy finish

th_13Finish.jpg

Admire your handy work before starting the hard bit

th_14LEDArray.jpg

Cut down your Experimenters board down to size measuring it up to the hole you cut in the Garnish

th_16LEDArrayBack.jpgth_15LEDArrayFront.jpg

I know this was an extremely crap soldering job; Solder all your LED's, Resistors and your wiring onto the board

th_17Wiring.jpg

Finally hook up the garnish to your car wiring in the rocker switch if you want to be able to turn it on and off, as a precaution I wired this to my ACC wire so it can only turn on while the key is in

Use THIS website to calculate the ohm's required for your array

Great walkthru there mate, thanks alot. I will try to fix my panel this weekend, hopefully it´ll work out fine :P

Just one question: what website to calculate the ohm´s?

  • 3 months later...

excellent guide, will do mine next week, anyone bought the leds from ebay

WHAT IS THE BEST SIZE LEDS TO USE 3 4 5 OR 10 MM

NARROW ANGLE 20 DEGREES WOULD BE BETTER THAN WIDE ANGLE 180 DEGREES I PRESUME

Edited by Dorifta
  • 2 years later...

sorry to res an old thread, but thought I would share a new way of doing this. I am going to use the new "tri" colour LED's witch is one LED with 3 colours, and 4 pins instead of the normal 2.

my plan is to have 4 try colour LED's to just lightly light up the "skyline panel" when the lights or parkers are on, then when the brakes are applied, another 7 tri coloured LED's will light up (same colour) and act as a brake light.

there will obviously be a 3 way switch to select between the 3 colours (red, blue and green). I will probably have this in the ash tray up the front so its hidden.

I've given it a lot of thought, and being an electronics geek I've already drawn up plans.

I've only just bought my S1 panel of a SAU member as I have a S2 R33.

heres a pic of the LED's I'm talking about, and I'll make sure I upload pics once its done and even a tutorial if enough people show interest.

I may consider doing this for others if they pay for all the parts :)

post-89929-0-31652800-1326800467_thumb.jpg

33 or 32? Im going to see how this one comes up first as I'm sure what I'm doing has never been done before, maybe I can help you out at a later date if your interested.

[/quotmoei

Are you talking to me? if so its an R32 I seen it on a R35 on the front Looks Beautiful

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...