Jump to content
SAU Community

Recommended Posts

Hey all,

I know it's been said many times 'if you want a manual, buy it from the factory', but I was wondering if anyone here has experience with a manual conversion on an R34 gtt? I'm after all the details and if possible, prices/specific workshps (I'm located in St Lucia, Brisbane and currently head to SR Motorsport at Kippa-Ring).

What are my options? Can I throw in an R33 box? How much would I be looking at for a second-hand Getrag box out of the GTR? I'm more than happy to shop in Japan (I know a bit of the lingo) so if anyone could give me some direction I'd be most appreciative.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/122779-r34-gtt-manual-conversion/
Share on other sites

Ok, so no replies...

Anyway, I've found the following for $3500:

box -- master cylinder -- wiring harness -- pedal box -- clutch + flywheel --- driveshaft -- dash meter panel

Does this sound reasonable? Is there much chance to resell the auto box to an R32/33 owner?

  • 4 weeks later...

hey. I'm interested in converting my Gtt to a manual too.

but it seem that no one has done it befor, not to a R34 anyway.

I got a mag at home that have an article on 'how to convert a R33 or R32 auto to a manual'. not sure which one model :D but i will check and let you know.

good luck for now. I have try and still tying to look for infor on the net in regarding to mod to a R34 and there don't seem to be much.

have you got any information?

It only stands to follow that there about 1/50th the amount of r34 on the road compared to r33, etc and that not many people have done this conversion.

The price to convert any new car is much more more than the price of an old shitter, and finding the parts is a much more expensive proposition.

If $3500 is true, its a bargain price if it is all that is required on a 34. I've only done this on an R32, not an r34, but it sounds like they are all the bits you'll need..

And the gertrag box? thats a 4WD box, and would require extensive / expensive mods to convert that to a RWD platform. Again, possible if you have thousands to spend, but if not... .

I can confirm the price above is genuine, hence I'm going to come out about where I'd be (financially) if I'd bought a factory manual.

The reason I was so interested in the GTR box is because I read Getrag supplied the same box for the JZA80 Supra, however I'm thinking this is not the case...

  • 1 month later...
I got a mag at home that have an article on 'how to convert a R33 or R32 auto to a manual'. not sure which one model :( but i will check and let you know.

what mag is this cus im interested in getting a copy

thanks

I got a mag at home that have an article on 'how to convert a R33 or R32 auto to a manual'. not sure which one model :( but i will check and let you know.

what mag is this cus im interested in getting a copy

thanks

Buy my stuff please. :D

Sorry my post is really off topic but I just realised.... Your car is pictured in Septembers High Performance Imports magazine, I am fairly new around these parts and got that magazine as I noticed the Top Secret V2 R34 on the cover.... You are famous dude!

Depending which state you are in, hopefully will meet you at one of the cruises or outings.

Drew.

Hey guys. Really sorry I haven't noticed this thread until now.

I am the second person that I know of that has done the manual conversion. We both went to the same place but used different parts.

I conveniently had a manual R34 wreck so I took all the parts from there except the clutch line going from the master cylinder to the slave which some fcuker stole from me.

I would recommend using some R33 parts for 2 reasons. First is that they are more plentiful, second is that R33 GTST boxes use a push type clutch whereas the R34 GTT box uses a pull type clutch. The only reason this matters is because when looking at clutches to handle big power, push type are about half the price of pull type.

You can get an R33 GTST gearbox for about $1500 if you can find one. R34 GTT boxes are similar in price but even harder to find.

If you do use an R34 box you can use an R33 GTR clutch as they are pull type as well and fit up no problems. Also stronger.

New clutch master and slave cylinders are not too expensive.

Pedal assembly not too hard to find. Tailshaft must either come from a R34 manual (just the front half needed) or get a tailshaft specialist to make something up when you get a yoke from an R33.

Any RB flywheel will fit, need a flex plate but that's cheap. Flywheel bolts aren't too cheap. So try to get them with the flywheel. Get the flywheel machined as you will be using a new clutch no doubt.

So parts cost you are looking at I'd say anywhere between $2200 and $3500

Labour, both me and the other guy I know of got Greg from Autosport Engineering in Kirrawee (sydney) to do it for $1500 drive in drive out.

Umm what else... The interior parts are very hard to find. Might get better luck at Yahoo Japan auctions.

Mine is a 4 door and I used 2 door parts. Same wheelbase.

Dash and steering wheel are extra and hard to find. About $300 for a cluster and $200-300 for a steering wheel.

Clutch costs extra - depends how much power as to which one you get.

Stock ECU will work fine. PowerFC plugs straight in too.

Anything else?

if you are going to use r33 pedal assembly...the brake pedal assembly ..4 out of 5 bolts bolt onto the original holes..You can make up a new hole position with longer bolts. Shouldne be a problem..

the clutch pedal assembly fits perfect :D

ive just put the pedal assembly in and the clutch MC.

Just got your Auto tailshaft today from Stans workshop and hoping to mod it soon..but i got to find the second half of the shaft..the taishaft specialist needs it whole so they can balance it wen they swap over the yoke.

after that, it should be like a basic CLUTCH change..

LOL yeh i think i might have to, meaning car as to be off the road :woot: , but i need to get the exact measurments...If anyone has a r34 Auto and manual tailshafts lying side by side, can you me if the lengths are the same...from the top of the yoke to rear diff connection.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...