Jump to content
SAU Community

Recommended Posts

Hello ,

As you are all aware new laws came in or are coming in on the modification of cars.

I had been pulled over earlier this year,and was called up to the epa for an appointment.

The epa ,interesting enough ,were looking for after market computers and boost controlers as well as boost regulators

.

All other items were not even discussed ie Pods,Intercooler,Fuel regulator,Turbo timer,Catch can.(Which are all after market units).

It was interesting to see the mechanic looking in places people hide there valuable electronics, and i though i was there for noise pollution.

Anyway, does anyone know the limits we can go with this law . what modification can we do without it being

against the law....I was told , punishment is in the order of $6,000 for each item.(Another interesting topic)

Which brings me to the point. Can a stock ecu, (GTR GTST) be tuned to perform as well as an after market one, be it an apexi or motec ?

Can boost be set without gauges and electronics ?

I am purchasing turbos , powerfc ,and avcr for my car.Should i leave the apexi and avcr out and spend that

money on cams,rods and baffle tank?

Your input would be great .

Thanks

Link to comment
https://www.sau.com.au/forums/topic/124170-tuning-a-stock-computer/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

The stock ECU's can be chipped, and then subsequentally tuned. (R33 gts-t is difficult)

At the end of the day its still illegal. The EPA can pickup on a modified stock ECU, and if they do, its the same as having an aftermarket one. Its defectable and the EPA will fail you :wub:

Basically anything that modifies emissions is just about impossible to make legal.

There is a level of extent there, and many tricks to "bend" the law.

Its a bit hard to go into over a internet forum.

I suggest coming along to the next SAU-Vic General meeting if you want, come find me (name is Ash) and i can go over many things.

There are a LOT of loop holes and ways the law can be "bent" to suit the application.

I'll admit im no expert. But there are some tricks and interpretations that i've learnt over the years (and the defects/EPA's) :)

Hey mate! I must say I am in a similar position to yourself and these new laws are stressing me a little - not because I drive like a 'hoon', but the discretionary part can/will be abused...

Anyway back to mods, try this link - it might be able to lead you to something useful...

http://www.skylinesaustralia.com/forums/in...topic=13305&hl=

Good luck!

Chris

The stock ECU's can be chipped, and then subsequentally tuned. (R33 gts-t is difficult)

At the end of the day its still illegal. The EPA can pickup on a modified stock ECU, and if they do, its the same as having an aftermarket one. Its defectable and the EPA will fail you :)

Basically anything that modifies emissions is just about impossible to make legal.

There is a level of extent there, and many tricks to "bend" the law.

Its a bit hard to go into over a internet forum.

I suggest coming along to the next SAU-Vic General meeting if you want, come find me (name is Ash) and i can go over many things.

There are a LOT of loop holes and ways the law can be "bent" to suit the application.

I'll admit im no expert. But there are some tricks and interpretations that i've learnt over the years (and the defects/EPA's) :wub:

hehe...how bout a thread in the vic members section away from prying eyes :)

The stock ECU's can be chipped, and then subsequentally tuned. (R33 gts-t is difficult)

At the end of the day its still illegal. The EPA can pickup on a modified stock ECU, and if they do, its the same as having an aftermarket one. Its defectable and the EPA will fail you :)

LOL, and i passed with my chipped one.

Count yourself one of the lucky ones thats for sure ;)

I know people who have not, and mine was checked for a CHIP aswell when i went.

Opened the cover and all on the ECU.

They are on the ball the EPA, no doubt about it

Count yourself one of the lucky ones thats for sure ;)

I know people who have not, and mine was checked for a CHIP aswell when i went.

Opened the cover and all on the ECU.

They are on the ball the EPA, no doubt about it

Damn. Before i went i just took off the sticker it had on it (some tuning thingy from japan) and i was glad it passed. The guy said that my emmisions are a little high and passed me.

ok...i get why it can be illegal b/c it modifies emissions - but isn't that a double edged sword?

I mean, the car can be made to run healthier and produce less emissions with an aftermarket ECU? so surely the EPA would take that into account wouldn't they?

The ECU is programmable.

Therefore, nothing stops you from altering it once you leave the EPA station.

Thats the issue with a modified/programmable ECU, and just because its got one tune now, doesnt mean you cant change it.

Its like most Vic laws and how they are administered... Its all based on assumption, not fact

ok...i get why it can be illegal b/c it modifies emissions - but isn't that a double edged sword?

I mean, the car can be made to run healthier and produce less emissions with an aftermarket ECU? so surely the EPA would take that into account wouldn't they?

When the sound test was conducted, which i though was stupid, my car was at 5100rpm.

This is an incorrect test.The epa are assuming the vehicle is 206kw which i stated was not a correct figure to be working with to start off with The revs are at 75 %peak power. At 5100rpm i have more than 206 kws at the flywheel...

How stupid is that believing the japanese gentlemans agreemant to be gospel,

My ecu had been modified in japan and tuned for there stupid 110r fuel. The inspecting officer...mechanic...

was more interested in after market computer and boost control unit....ASH you have not made any comments on boost..

Iam interested to hear your opinion.

Regards

When the sound test was conducted, which i though was stupid, my car was at 5100rpm.

This is an incorrect test.The epa are assuming the vehicle is 206kw which i stated was not a correct figure to be working with to start off with The revs are at 75 %peak power. At 5100rpm i have more than 206 kws at the flywheel...

How stupid is that believing the japanese gentlemans agreemant to be gospel,

My ecu had been modified in japan and tuned for there stupid 110r fuel. The inspecting officer...mechanic...

was more interested in after market computer and boost control unit....ASH you have not made any comments on boost..

Iam interested to hear your opinion.

Regards

The testing speed of 5100rpm is correct for the RB26 engine in the Skyline GTR as per the EPA specifications on exhaust testing. It has nothing to do with how much power the car has at the flywheel or anything to do with what you feel is right or wrong. The gentlemans rule means nothing to the EPA and australian standards as far as I can tell. Boost is irrelevant, its simply a pressure level. Why does everyone care about boost so much?

post-2054-1151568525.jpg

But the EPA couldn't care if you make 10rwkw or 300rwkw.

All they care about is emissions. If you change the actuator on the factory turbo to a 1.2 bar spring and they don't see it then they most likely wont know it is there. They don't plug a pressure guage into the manifold and have a specific test for boost. They simply look for stuff that alter emissions (that are measurable),

loud exhaust

screamer pipes

ecu change

piggyback ecu fuel systems

air intake modifications

intercooler modificiations

running 5psi or 7psi or 11psi means nothing to them. It's how loud the exhaust is, what gas comes out the ass end, and so on.

When the sound test was conducted, which i though was stupid, my car was at 5100rpm.

This is an incorrect test.The epa are assuming the vehicle is 206kw which i stated was not a correct figure to be working with to start off with The revs are at 75 %peak power. At 5100rpm i have more than 206 kws at the flywheel...

How stupid is that believing the japanese gentlemans agreemant to be gospel,

My ecu had been modified in japan and tuned for there stupid 110r fuel. The inspecting officer...mechanic...

was more interested in after market computer and boost control unit....ASH you have not made any comments on boost..

Iam interested to hear your opinion.

Regards

The test used to be around 4600 for the RB26.

And, since the law/rule was changed to 5100... a 100% Stock GTR with a 100% Stock Exhaust, no longer passes, believe it or not if i recall correctly.

So im not sure of where they get thier numbers from, who governs the changes/are they tabled for public input etc. Also where they get thier power/load and emission ratings from

I dont make comments about being under load (on boost) as the EPA does not care about that.

They are after idle emissions. If your idle emissions are not upto scratch, then under load its going to be worse.

The EPA basically check to make sure the stock boost solenoid is in place, and its connected.

There are ways to increase boost, without a EBC/different solenoid etc.

If they didnt open your ECU cover, again, count yourself one of the lucky ones.

The usually plug into the consult port, and then can see if the O2 sensors are working from what the EPA Officer told me last time i was there and i had quite a long discussion with him, as i will on my next visit in the next few months

My car being pre 90s didnt have the consult port :D So in that respect there is no way of knowing and failing on that part with my car. As long as exhaust emissions are within the tolerances i get to pass is what i took from the last visit there last year.

The testing speed of 5100rpm is correct for the RB26 engine in the Skyline GTR as per the EPA specifications on exhaust testing. It has nothing to do with how much power the car has at the flywheel or anything to do with what you feel is right or wrong. The gentlemans rule means nothing to the EPA and australian standards as far as I can tell. Boost is irrelevant, its simply a pressure level. Why does everyone care about boost so much?

Where do you think they got the rev from then.?(from mid air)..

The manufacturer states the power of the car and they work out at what rev is 75% of the power produced.

The rev is then canculated...noise...is then tested.

I thought i was there to get a noise test conducted...they were just looking for how much power i had .

You see guys....we did not pay the government $100,000 for being able to have that power on the road.

We did not buy a 911,ferrari,masa. and they are upset .

I have heard a few of these cars and believe me they are loud , but you dont see them getting epa test.

Edited by 700HP-GTR33

You'll find that a Ferrari has winged doors in the exhaust that only open above a certain RPM >_<

And other manufacturers cars might sounds loud under load, but remember... and this is what you are forgetting.

The test is done without load.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey everyone, I recently bought myself a 2001 Nissan Stegea M35, and I've had a few issues that I had to fix, my car would start intermittently and I had a bad rocker cover leak, after a couple days of looking I finally found a part number that interchanges with the OEM starter as the OEM starters at $1300 and I can't afford that, this starter was only $270 and I replaced the start and still had the same issues, I posted a video asking for help online and it went very well, some guy said it was probably a bad ignition switch so I took my dash apart and turns out my ignition switch was half screwed in and was loose, once it was tightened it fired right up, I found a local place called "Boost factory" and they sold me a part of OEM Nissan rocker covers, they were $600 which was a shocker but I couldn't find them anywhere else, so I installed them and fixed my oil leak as the old rocker cover was cracked and warped, I now need to replace my boost air inlet hoses as they have some cracks.
    • I am being real ocd and do not want to make amy mistakes so appreciate all help provided. I am overly cautious so asking for opinion even if i know the answer   few questions,   1.re tensioner, should spring be greased lightly?    2.tensioner has two washers , one pressure washer and other has recessed/ seat. I am going to put the recessed one facing tensioner where edges are cut out and pressure washer on top   3. my car has custom triger kit sold few years ago by guy who initially built the engine. I moved the crank gear and it moved in and out easy, only way to remove belt is to slide the crankshaft gear forward which I did. I have seen these being very tough to move , anything to do with my woodruff key?   it has a crank sensor shown in purple which I assume reads from the 12 teeth position mounted to the crankcase gear   4. timing belt doesn’t have arrow stating front or back just a arrow which I think is direction of rotation . Do you agree?   5.i figured out why my crankcase cover was worn as there was no washer installed over the crankcase cover before the harmonic balancer was put in place. It is missing, anyone knows the part number? It looks like this https://justjap.com/products/genuine-nissan-crankshaft-timing-gear-rear-plate-washer-nissan-s13-ca18-a31-r32-rb20-r33-r34-c33-c34-c35-rb25?currency=USD   https://tinypic.host/image/IMG-4535.382Zy2 https://tinypic.host/image/IMG-4537.382dSz https://tinypic.host/image/IMG-4534.382q4U  
    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
×
×
  • Create New...