Jump to content
SAU Community

Recommended Posts

no resistor pack - i thought you need that when your running GTR injectors cos theyre low impedance. these are high impedance top feed specifically for rb20 replacement, as far as im aware.........

arhh k sorry dude i wasnt 100% sure thats why i asked hehe :)

Edited by CruiseLiner

I think you guys are trying to confuse everyone here.

The rb20 runs high impedence injectors and no ballast resistor which is where cruiseliner is confused.

R31nismod is talking about the ignitor that sits at the back of the engine on top of the coil cover piece.

The microtech doesn't necessarily need the ignitor and it definately doesn't need a ballast resistor.

To answer some of your questions, the resistance shoud be between 12 and 14 ohms, the rail is stock, i don't know what collars you are refering to but the assembly you have is complete as the rail holds the injector firmly in place unlike hosetail injectors or side feeds which do have a collar, and i suspect the pintle cap has melted as a result of your engine dying and combustion has gotten back into the intake. A fuel injection specialist will be able to clean and flow your injectors and replace the pintle caps, orings and insulators and tell you if they are still ok.

I suspect that it wasn't running fine if you cracked a piston :O Find a new tuner once the new engine goes in......

Edited by BHDave

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...