Jump to content
SAU Community

Recommended Posts

Hey just wondering who is heading out tonight we will be there so if you guys who are going to paintball come along if you can. would like to know who Daniel and I will be Aiming for :miner:

We will be out at bout 9.30ish

You must have been late, we all headed off about 10.40pm

yeh i didnt get out till 11. was at my mums all day.Went through at half past not really expcting to see anyone and this huge mob of chicks in formal dresses waved and blew kisses at me :D

I had the GF in the car though so i kept going :P

thats cuse you is gay lolol

Thanks Dan, you got a motor to push those wheels yet? Take that :P

Yeah not bad night, good to see a few out still, Stung a little with the when am I going to buy a real Skyline? But I'm ok thanks! I thought it was not illegal to buy a GT-R and not no its history? Found out what a KPGC10 and KPGC110 are yet?

Good to meet you all, see you out there!

G

  • 2 weeks later...
Josh, do some work =P

I might come out, depends on what time I finish dinner with the other half. I'll still drop by and see who's still there.

:kiss: Hell no its friday. I'll try and make it...theres a first for everything

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...