Jump to content
SAU Community

Recommended Posts

i know this question gets asked over and over again, but this one is somewhat more specific and im nto just some dreamer posting a useless question just to kill some time. im about to import a more drift orientated car that will still c the street sometimes that has an rb26 in it. compliance and importing etc is no problem as i have a mate who is an importer but will be doing it at mates rates 4 me. ok, anyway, iv whittled the list down to the following....

1) 32 gtst with 26

2) 31 ceffy rb26

3) s13 with an rb26

or he already has a 450hp 32gtr with a26 out of a 34gtr in it on the boat, but im thinking the added weight will be a negative (and of course ill have 2 kill the 4wd with an atessa controller).

any advice would be much appreciated because it seems everybody i talk to gives me different advice and i want to make the most informed decision i can. i was thinking the extra weight in the front of the sil would throw the balance out too much but just thought id c what you guys have to say.

cheers

ardie

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/
Share on other sites

The S13 will probably be the cheapest choice. but if you are going to drag all that weight, I don't know... its just a *little* heavier than an rb26. If you want a heavy big power engine, then get a bigger car. My personal opinion is no.

The Cefiro is popular because its a 4 door, so it has a long wheelbase (don't know about track width...). I like 4 doors...

as for the R32, well, umm, yeah... but go a 4 door (same reason as the cefiro, only a little shorter). Apparently the sr20 gives a great balance, it being 4 cyl and alloy, not 6 and cast.

and as for the GTR, well, it is front heavy, and still doesn't have the wheelbase of the larger cars. Then again, when you arn't drifting, just re-enable the attesa (yeah baby). My theory is that attesa will help to cancel any drift tendencies while on the street.

All this can be found on this forum, and a hundred others.

Now to indulge my fantasy, get a 4 door r32 gts4 and put in the rb26 (and set it up for drift). Personally, I'd go the gtr. can never have too many gtr's on the street.

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2354711
Share on other sites

i don't have a drift car

i havent gone and drifted my car anywhere

But just looking from my point of view

if your getting mates rates, and by looking at putting a rb26 in any of those cars you stated

How would the weight balance be in a r34,

i have seen a r34 in japan driftin and looks pretty mad

(only problem it might of costed a bit to get it to that stage)

Plus i havent seen a r34 driftin in QLD,

you will stand out from other drifters

And would be awesome to see.

Only problem once again is how much money ya wanting to spend

if you even like the r34, and if you have already considered the option.

if you simply want to just drift, i would go with any of those options you stated

But in my opinion if i wanted to drift a car, that not many other ppl do drift, i would look into a r34

But choosing from those 3 options you have given

I would go the r32, just the fact i see too many s13's and ceffy's out there, and would like to see more skylines in the game.

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2357030
Share on other sites

i want an rb26 because its so easy to get power out of and they are bulletproof even when stock. to many of my freinds who run SR's seem to have problems but the few people with rb26s seem to have "less" problems because as we all know, drift cars ALWAYS have problems to some extent. im currently looking that a 1990 a31 ceffy with a 26 in it because i think it will despense the added weight of the 26 more evenly due toe the larger size and weight. still not fianlised so any other opinions are more than welcome

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2359195
Share on other sites

you dont need power to drift

if your going to import a drift only car...

go get urself an s13/s14/s15/180sx already build.. no point removing the sr20... it has good weight balance plus you can get easy power out of it (just drop a gt2835 or gt3037 in it)

also weight isnt a HUGE factor when your starting out but once you get good. you will want to drop the weight abit if it something like.... 1450kg

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2360479
Share on other sites

sorry guys i didnt really outline i guess, i already have a car set up 4 drift, a sII 33, zeal adjustable coilovers, whiteline bushings, FMIC, Power FC, hks3037R etc etc all the usual stuff, main focus has been on suspension but im sick of it, i want something a little different, and you dont see many ceffys down here in vic

as for the car already being built, thats exatly what iv been going to do all along. iv bid on an a31 1990 ceffy with an rb26 in it, zeal coilovers, strut braces, bride seat, power FC Djetro....hjopefully i win, if not theres still a chance i might change my mind, but i love the stealth facor of the ceffy cos i seem 2 get a fair bit of trouble from the officers in my 33 wich is part of the reason im over it i think

and ebola, u and ur god damn gtr love affair lol if u ever get the $$$ i can get u an rb26 halfcut from japan for cost price, maby then ull stop talking about them lol

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2362669
Share on other sites

First off the R32 four door is exactly the same wheelbase and dimensions as the coupe (the roof is slightly higher) and weighs 20kg's more. If you import a 1990 model A31 with heavy modifications how are you going to register it? SEVS if it is available for ceffies which I'm not sure if it is yet, requires the car to be completely dead stock (Rb20 motor) and everything else removed. This includes suspension, motor modifications, wheels and everything else that isn't original.

Just to put it clearly any car built in December 1988 and before can be registered with the need to follow the sevs rules. That cancels out the R32. The S13 would be very hard to find with a motor other than a SR made for drifting. You best bet if you want to import a car that you want to use to focus on drifting would be a A31 cefiro 1988 dec or prior. It is a pretty common thing for A31's to have the RB20 removed in place for a RB25DET and would be an easier find.

As for RB26's, there really not as reliable as you might imagine. Ask the dozens on GTR owners that have imported GTR's under the old 15 year rule that have had cars come over with blown engines. Also GTR's are expensive motors to rebuild as well. As for using a GTR for drifting? They are 4wd and front heavy. GTR's were built to be track cars.. not drift cars..

My 2 cents

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2372175
Share on other sites

Oops - 4 door is longer... don't have the specs on the wheelbase (makes sense)...
First off the R32 four door is exactly the same wheelbase and dimensions as the coupe (the roof is slightly higher) and weighs 20kg's more.

I must need my eyes checked... 'cos Baz is right...

I think I'll retire and just watch the thread...

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2372583
Share on other sites

Definatly go for the Cefiro option..... but as Baz has stated the 26 CANT be in-expensive, put it this way if and when it does go, think of the cost to rebuild it $$$$ there are a couple of the boys over here in SA from Delirium now have Cefiros and they have just chucked the 25 in it and that is gonna be more than enough to get the Cefiro thru what you wanna put it thru!

And as stated before GTR's are a Grip race car not drift.

and as for a S13 with a 26 in it.............Don't bother it would be like a GTR drifting....front heavy and not too mention POO!

If your dead keen on a RB26 then head to the Cefiro it will at least handle it alot better! and if there aren't too many Cefiros in Vic then run it, Do what you wanna do mate not what someone else thinks phat!

Edited by Deluxe
Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2382352
Share on other sites

The RB25 can sustain more than enough power for your drifting needs. They can be run reliably on roughly 350hp day in day out on stock internals if you give it lots of TLC. Which is more than enough power for drifting. And no offense man it sounds like you haven't really done much drifting before in the past. So drifting on something with a bit less power is a good place to start. A S13 with a black top SR (late model 180sx's) are a very good platform to start drifting on.

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2382734
Share on other sites

as drifter said why on earth is a rb26 more pricey to build than a rb25 or rb20?????? they all got 6 pistons and rods, bearings, rings so wheres the extra cost? its a big myth i reckon because people always go serious builds with 26's and end up spending 7-8k where as rb25s usually rebuild stock for alot less.

an rb25 with same specs as a rb26 is gonna be identical in costs. how couldnt it be?

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2386159
Share on other sites

as some others have said above. RB25DET is better than RB26 for drift... cheap bolt on mods, enough power for drift and cheap initial purchase price compared to an RB26, which isn't gonna be that much of an improvement in drift setups... you're not building a circuit racer or drag car here. Your primary concern is to make sure the engine dosen't blow while you sit on the rev limiter all day...

Getting an AWD skyline/cef for drift is dumb, purely because the front axles add weight and reduce steering angle, which you'll need to get good lock. Again, not really building a circuit or drag car to need AWD.

If I were to build a car just for drift on a limited budget, I'd just get a regular manual Series 1 R33 GTSt. You can have one landed complied and registered for around 10k these days, you've got a standard RB25DET and if you put some bolt on induction mods, strip it, take out HICAS, change the suspension and add a mechanical LSD you're well on your way to a sweet sweet drift car for under 15k. Panels are cheap as hell and spare parts are so cheap... perfect for a drift car. Plus it's newer than a rusty old A31, S13, or R32.

f**k being different... I'm sure your bank balance dosen't care if you're the only monkey on the track with a certain type of car.

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2386182
Share on other sites

ummm dont mean to be rude but maby u guys should look at what iv got on my car already....i got a 33 with all the basic light tune mods (turbs, management, fuel system...) makeing 220rwkw. As for the gtr question, it was mainly out of curiosity as i havnt seen any while iv been at the track (not that iv been THAT many times, im by no means a seasoned drifter, u can ask my rear quarter panel that). the only reason im after a 26 is beacuse as i said before, i dont really want to go any further on my car until im sure i wont be dissapointed with the end result.

as for finding the car, it is not an issue. i have a mate with a brother in the auto buisness in japan (the importer) and he assures me he can find them on a regular basis, even showed me a couple the other day 2 prove as i was cynical at forst aswell.

given the advice you guys have given me along with that of a few of my more informed friends, im starting to have 2nd thoughts about getting rid of the 33 tho, but i thoght they wernt really the greatest because of thier increased weight, whats you opinions on this?

also, i dont really see how a 26 can be THAT much more expensive than a 25 to rebuild, and as im a little nerd whos living at home (and will remain there unitl im 46, single and unemployed) while getting a grand a week from work, i have more than enough money to throw around (sorry if that sounded like bragging, but im just trying to outline my situation 4 u guys)

oh and no offence taken about u assuming iv never drifted, like i said, im not a seasoned pro by any means, i just have a lightly tuned car that i want to turn into more of a dedicated drifter that can still see the streets occasinally. even driveing my car as it is now is a labour due to the suspension (really takes a toll on your back) and gate (every time im on full boost im worried about cops in traffic).

as for complaince of the car, i cant really say much about that at the request of my friend, but it can be done.

Link to comment
https://www.sau.com.au/forums/topic/127468-drift-car/#findComment-2403664
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...