Jump to content
SAU Community

Recommended Posts

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

increased fuel consumption, also using a 1GZE SC is like using a stock trubocharger off a GTSt. Unless u go for a $6000 vortech/eaton centrifugal supercharger (which is like puttin a T88 on ya GTSt) you'll never get optimal results out of a supercharger.

The reason Nissan never came out with em is that in small capacity cars (3.0L and under) its not completely efficient.

if u do consider supercharge

the car will be be more like a 4.0L aussie six

plenty of torque and power, but power wont peak that high in the rev range as our cars currently do.

u can get SC that can rev and stay someone efficient at the higher revs, but it also cost money

not necessarily, those are the oldschool superchargers that work better at higher revs.

If you look at the boost charts, the turbo charger has an exponential boost (very low boost for initial phase and very high boost after the sweet spot). A supercharger however is belt driven, ie constant. It has a linear looking chart, therefore you'd have better midrange boost than a turbo, and much better pickup at the lower end. You do however have to tune it so you don't overboost at higher revs.

eg: say hypothetically your max boost is 14psi

REVS.-> 0 . 1000 ..2000 . 3000 . 4000 . 5000 . 6000 . 7000

SC.....-> 0 ... 1 ...... 4 ...... 6 ...... 8 ..... 10 .... 12 .... 14

TURB.-> 0 ... 0.5 .... 1 ...... 2 ...... 4 ...... 8 ..... 11 .... 14

however true linearity is only achieved by centrifugal superchargers (I think, not sure) and thems the more expensive ones.

Oh and as for the q about the ECU having to be modded... NFI, I gave up and decided to go for a GTR b4 I could investigate it.

there are companies which specialise in superchargers. go through your yellow pages and find one and given them a call and have a chat about your options. i'm sure they will let you know all that you have to do.

SC can't be too bad of an idea if mercedes chooses them over turbo's. also many american professional drag cars use superchargers because of their low-down torque and power.

would be great to see a SC skyline zoom past any gtst and do well against a gtr!

u gotta spend sum serious cash for that. The company I wastaling to was adelaide based, and they specialised in supercharging civics and the like, so I gave em a buzz... think they were working on a supra at the time, either doin a super/turbo twinny or a straight super, sumfin liek that, they were the ones that gave me quotes for manifold fabrication n stuff.

I got their email at home, I'll post it when i get back from work

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...