Jump to content
SAU Community

Recommended Posts

This thread makes me wanna cry over a couple of G's so I get offered a couple of GTR's for 15k

Dont just cry...Cry like you were 2 years old, use the fists, the feet - wave and stomp like a mad man - that will def get you a ferrari!

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

no, its not people pricing their cars too high... its a matter of everyone wanting something for nothing these days...

love it how people expect to buy stuff for cheap then when they sell soemthing BAM almost retail prices and whine when theres no interest

What a mad few days!!!you were right,I was wrong....so Im selling the boat this week (Its in the Trader,tomorrow Thurs $20k) and I went and ordered this little beauty on Saturday from JSA down in VIC! thanks for all the good wishes,catch you at the QLD meets? I'm sure you won't miss me :P nearly forgot to say it's a tad over 15k :D

<--------------

Well done.

You're still a dickhead.

mmmmm.........probbaly going to get flamed for this. but i dont dissagree with what the OP is doing. i've lived in australia and the UK and yes, the car market is very different.

Cars in Australia are overpriced.

Skylines are overpriced. Reeeeealy overpriced. I think they're absolutly fantastic cars in original condition but here's the reality.

I won't take any car I own onto a beach. Salt, you see, does terrible things to metal. Australian cars also have drasticly different design requirements when compared to many countries.

Also, our car market is regulated (so prices are higher across the board) to protect the local hoon market.

Expensive for a reason, not just consumer blindness.

What a mad few days!!!you were right,I was wrong....so Im selling the boat this week (Its in the Trader,tomorrow Thurs $20k) and I went and ordered this little beauty on Saturday from JSA down in VIC! thanks for all the good wishes,catch you at the QLD meets? I'm sure you won't miss me :P nearly forgot to say it's a tad over 15k :D

<--------------

Would you take 15k for the boat?

Hope not to much more than 15k - looks like an abortion.

What a mad few days!!!you were right,I was wrong....so Im selling the boat this week (Its in the Trader,tomorrow Thurs $20k) and I went and ordered this little beauty on Saturday from JSA down in VIC! thanks for all the good wishes,catch you at the QLD meets? I'm sure you won't miss me :blush: nearly forgot to say it's a tad over 15k :blush:

<--------------

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...