Jump to content
SAU Community

Fmic Question

chopobo

By chopobo,
in Engines & Forced Induction

 Share

Recommended Posts

Munkyb0y Grand Master

Munkyb0y

Posted
Posted (edited)
Dont bother if stock boost. I'm running 10psi thorugh a r34 SMIC and it is fine. A FMIC at 10psi or less or even on the stock turbo is a bit of a showy thing rather than a performance gain.

Unless your on boost around a track for hours , then a FMIC might be worth it.

so u reckon the r33 smic is sufficient? or the r34 smic is a worthwhile upgrade on my r33. it gets up to 9psi on a cold night with pod and exhaust. i'm worried about the summer temps though. havent been there yet.

Edited by Munkyb0y
Munna1 Proficient

Munna1

Posted
Posted

A GTT intercooler on a R33 GTS-T is a very good upgrade it is effecient for power levels up to 200rwkw.

my 2 cents

For those saying the power increase is due to less pressure drop id say you are correct but its not because more boost is generated. Boost is messured after the intercooler remember. Power can be gained on the same boost level because the air is cooler this is for 2 reasons

1. less pressure drop so the turbo doesnt have to work as hard to produce the same boost

2. The efficency of the intercooler (air cooling is better)

The colder the air the more oxygen it contains and the quicker it burns. Boost does make power but sometimes quality of air is better than quantity.

If you choose to run stock boost not much will be gained by installing a FMIC because the stock one is efficent at this level.

I was running 10psi with the stocker then upgraded to a hybrid FMIC, I gained heaps of power on the same boost

cheers

Kennedy Mentor

Kennedy

Posted
Posted
hey chopobo, u rekon u could post up a pic of front of the car and the engine bay, just wana c how they fit up, as im thinkn bout getting the same kit

I installed the gktech kit aswell and it seems to fit well. I'll post some pics this weekend. (Cutting back an S1 bar is TEDIOUS!!!!!)

TTT Grand Master

TTT

Posted
Posted
does the GTT smic fit straight onto the r33? as i've been lead to believe?

YES.

It is a DIRECT bolt on.

Unbolt stocker, replace with the R34 one.

On the R32, one of the end tanks are on a different angle and it needs mods to fit that.

But for the r33 and stagea, it fits straight on.

PAUL - SK had stated previously that the R34 smic was used in his R32 with the rb20 at 220rwkw.

He did have some temps that he posted here.

have a search for a thread with R34 intercooler and SK in the search options from a few months ago.

khunjeng Veteran

khunjeng

Posted
Posted

here is a bick of the GTECH kit on my car. I replaced a 34GTT SMIC for this one.

gtech.jpg

I'm running 16psi though it an ran it up to ~280rwkw last week. It could go more but my injectors were maxing out. Runs fine, I see no problems with it at all. Although it was installed with a new turbo setup I get max boost at 3500 and it cains.

this is all with the plate in the front :) next weekend this will be moved

GKTECH Mentor

GKTECH

Posted
Posted
here is a bick of the GTECH kit on my car. I replaced a 34GTT SMIC for this one.

gtech.jpg

I'm running 16psi though it an ran it up to ~280rwkw last week. It could go more but my injectors were maxing out. Runs fine, I see no problems with it at all. Although it was installed with a new turbo setup I get max boost at 3500 and it cains.

this is all with the plate in the front :) next weekend this will be moved

gk gk gk gk gk gk, not Gtech, gktech!! lol

Looks nice mate, do you have any engine bay pics?

Greg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...