Jump to content
SAU Community

Recommended Posts

HI! everyone i got an R33 GTSt wrecking at the moment ,i havnt made up a list yet or price will do that on tuesday afternoon.I will take any inqurie if anyone are chasing for R33 GTST parts till the list come up .the car been hit on the left front bonnet,guard and LH door are no good.that all for now list be up on tuesday afternoon.

pm me or email me on [email protected] or call on 0415642296.din.

post-21589-1154426805.jpg

post-21589-1154426979.jpg

post-21589-1154427012.jpg

post-21589-1154427031.jpg

post-21589-1154427051.jpg

post-21589-1154427086.jpg

post-21589-1154427108.jpg

post-21589-1154427169.jpg

post-21589-1154427190.jpg

post-21589-1154427220.jpg

post-21589-1154427346.jpg

post-21589-1154427425.jpg

post-21589-1154427573.jpg

post-21589-1154427599.jpg

post-21589-1154427668.jpg

post-21589-1154427752.jpg

post-21589-1154427773.jpg

post-21589-1154427853.jpg

post-21589-1154427884.jpg

Edited by dinzlr
Link to comment
https://www.sau.com.au/forums/topic/128339-wrecking-r33-gtst-whole-cars/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

hmm dude would you have the plastic covering bit on the side of the driver seat??

You know that black looking thing, that covers the reclineably push lever thingy??

You know what im talking about?? Its just one bolt..

20bucks??

Edited by siddr20

Hey mate,

Are you willing to sell parts off the engine, or are you planning to sell it whole?

As I'm after the "U" shaped rubber hose that goes between the two vents on the rocker covers, and also the knock sensor loom.

Cheers, Ryan

hey dude you would have it.. I can see bit of it from pic 2..

look at the driver seat. Look at the bacl thing under it sorta..

You know when you put the lever up so the seat reclines..

Hmm i dont have camera to take a pic of mine..

look at pic 2, you can see it..

Edit: This pic: http://www.skylinesaustralia.com/forums/in...st&id=49430

Edit 2: How much for that gtr wing?? Cheers

Edited by siddr20

Do you have the plastic bit under the drivers side? Under the steering colum, the plastic that covers the fuses and the wiring under it etc.. $10?

Driver side floor mat?

Power steering pump? (Just want a rough est on price)

And if you are wreaking engine (though I doubt it) CAS Whole unit.

Cheers

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...