Jump to content
SAU Community

Recommended Posts

Trying to find out of my gearbox has a push or pull type clutch..

It probably is a dumb question but im running out of options trying to figure out if my new clutch will go in or not, f**k r34 N/A's and their assortment of parts

Hopefully fast will tell me. It worked for my diff :happy:

er34010972

Thanks

th_er34.jpg

this is the illustration of gearbox and clutch with part numbers

th_clutch.jpg

Edited by SkyHi_33
Thanks alot baron. Can i have a screenie of it with the list of factory options (if any) ? Thanks again mate

Big rear Brake

Super fine hard coat

advanced aero system

rear fog lamp

multi display meter

audioless

rear wiper

cheers

Can you please check this VIN out - supposed to be a R32 V Spec Gunmetal colour, van you check colour & whether V Spec?

Engine Number: RB26037275A

VIN Number: 6U9000BNR32304958

Thanks for your help

regards Mike

Edited by Mike Rowe
I always find R32s ridiculously hard to understand, but it came with 17s from the factory if that helps. Build date fits with being a V-Spec. Colour code is KH2.

Its a vspec. Looks like you finally found one mike.

Im the opposite...i can understand r32's but 33s n 34s make no sense :P

Edited by babyskyline
Its a vspec. Looks like you finally found one mike.

Thanks guys, its excellent the service you provide!

Now just need to make sure the car is in good condition and get it for the right price.

The clour cod - does anyone know if that fits being the gunmetal grey?

regards Mike

can someone try this one please?

BNR34-004512

and whats all this jargon-> GGJPRWYR34ZDAAAKCD?

th_casfjg.jpg

im not too sure what the rest means, i cant translate Japanese on my program but someone else should be able to help you out.

Thanks guys, its excellent the service you provide!

Now just need to make sure the car is in good condition and get it for the right price.

The clour cod - does anyone know if that fits being the gunmetal grey?

regards Mike

KH2 - Gunmetal Grey Metallic

so yes, same colour.

could I please get some help on my model codes for the 33 gtr, I'm trying to find out what exactly the car is and what it came with from factory

my model code is GGJPRQFR33ZDA-----

So far I have got:

G - 2 door

GJ - RB26DETT

P - ????? 4WD

R - ?????

Q - GTR

F - 5 speed manual ?

R33 - Model

Z - ????

D - ????

A - ????

post-19425-1242869233_thumb.jpg

thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...