Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • 5 weeks later...

I have a spare set of rb25det coilpacks in the garage at home, car wasn't missing or anything, just replaced them with splitfires due to upgrades. Happy to lend them out to anyone who needs them to troubleshoot. From memory they aren't cracked etc.

Hey everybody,

I'm wondering if anyone has a stock R32 exhaust system, cat back or whatever to lend. i got failed at dickson for the second time after getting it quitened down, apparently it was only 1.5db quieter, by ear its heaps quieter though.

Any help or advice as to what i can do would be greatly appreciated!

Thanks!

p.s. won't need it until the first week of jan now because dickson won't be open next week i don't think.

Hey everybody,

I'm wondering if anyone has a stock R32 exhaust system, cat back or whatever to lend. i got failed at dickson for the second time after getting it quitened down, apparently it was only 1.5db quieter, by ear its heaps quieter though.

Any help or advice as to what i can do would be greatly appreciated!

Thanks!

p.s. won't need it until the first week of jan now because dickson won't be open next week i don't think.

I've got a hsv pea shooter muffler, which got me past rego. only the end piece though, had to get the exhaust place to cut the muffler off my exhaust and put in a flange plate. Can lend it to you if you want.

I dont think that it will fit then.

Sounds like your exhaust from the cat back is all one piece, which means that you will need to have it cut and flanged somewhere around the diff so that you can keep a "rego muffler" on hand for these situations.

is it possible to take the "rego muffler" and my car to an exhaust place and ask them to cut it and flange it so it'll work? or is it not worth doing that?

If you go to an exhaust shop like Powatone in Fyshwick for example, they will cut and weld on a flange for you and make up a rego muffler for about $150.00 - $200.00, and its always worth having the muffler for the future because you never know when you might need it.

:D

  • 2 weeks later...
I have a stock R33 Gtst BOV if you need it.

that would be sweet Mick, I have ordered one in the mail (off the forums) and paid for it last Saturday. Was suppose to be sent by express post but still nothing in the mail..

If it doesnt arive by COB today (Friday) I will need to borrow it on the weekend to have it on the car by Monday arvo.

If I need it ill PM ya..

I'll also get you a 6ey, what beer do you like ?

cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...