Jump to content
SAU Community

Recommended Posts

the series 1.5 came out in 95 only i believe - check your coil packs and follow the plugs that plug into them. If it plugs into a square box that has another plug connected to it going to the engine harness then its a series 1 engine.

If its just pluged into a plug with no square box then its a engine wich is a mix between series 1 and series 2

Its got coils with ignitors built in and it does not have a plastic front wheel on the turbo but still has ceramic rear (same as series 1 turbo)

well my car is a r33 series 1 style ....but it has the series 2 motor in it , the car was made in late 1994....so what have I got a series 1 or 2 ...or the rare SAU 1.5? hahahahah

.....oh this is the motor which was made with the car! not dropped in after!

they do

yeah i thought series 1 had variable cam timing too.

also this tps plug not used on S1 manual, but is used on S2 manual. Dunno if that applies in the R32 setup though.

post-29392-1154923525.jpg

Edited by Munkyb0y

thats a series 1 motor. series 2 have a rounder tps, and it has 2 plugs (although both not always connected).

as for the series 1.5, they weren't a true model, but just a mix match. they have a series 2 wing, series 1 interior, series 1 bodykit, and most have a series 2 motor, drivers airbag as standard.

Edited by mad082

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...