Jump to content
SAU Community

Recommended Posts

Hi, I've recently just been wondering about a product i found on Ebay:

8d_1.JPG

^^ it looks as though its only able to be angled downwards a little. probably to hide the plates from speed camera's etc. I want it so that its like the pic below!

LicenceHolderSML.jpg

I was wondering if anyone had this installed on their car? Do you think the ebay product will be able to be angled as much as the one on the S15? I've got a stock front bar.. im not sure if it'l work as well as the one on the S15. Anyone with this product, feedback and pictures will be much appreciated..

And before anyone starts dissing it.. hey.. there are things you just want to have on your own car.. it looks so cool LOL.. plus it'l be practical for track use as it moves the plate out of the intercoolers face.

Ben.

Edited by chinkeboi
Link to comment
https://www.sau.com.au/forums/topic/130089-fold-away-license-plates/
Share on other sites

I reckon if your car got looked at by vehicle inspectors/police they might look at you with a sparkle in their eye and decide to lighten your wallet a bit over the matter

plus it'l be practical for track use as it moves the plate out of the intercoolers face.

what ever happened to taking the numberplate off when you go on a track when you're worried about airflow to the intercooler?

It only be useful if you know you are speeding and going past a camera.

Otherwise whats the point of having it?

The number of times you speed etc etc, you wont have enough time to quickly press a button and make the number plate go up b efore the flash goes off. Also half the time you wont even know there is a camera. most of the people get done un-expected!!

but none-the less a fancy thing to have.

Edited by siddr20

i actually had one where with the weight of the wind, would push the plate back into that position. mind you this only happend once i removed a stopper but yeah same diff

Edited by P-S-I
Hi, I've recently just been wondering about a product i found on Ebay:

8d_1.JPG

^^ it looks as though its only able to be angled downwards a little. probably to hide the plates from speed camera's etc. I want it so that its like the pic below!

LicenceHolderSML.jpg

I was wondering if anyone had this installed on their car? Do you think the ebay product will be able to be angled as much as the one on the S15? I've got a stock front bar.. im not sure if it'l work as well as the one on the S15. Anyone with this product, feedback and pictures will be much appreciated..

And before anyone starts dissing it.. hey.. there are things you just want to have on your own car.. it looks so cool LOL.. plus it'l be practical for track use as it moves the plate out of the intercoolers face.

Ben.

I saw one of these on the front of a GT-R when I was in Osaka and it looked like a great idea ! The one I saw was spring loaded so the at a speed of like 80kph or over, it would fold back/flat and then return to the normal position when the speed dropped again. I looked everywhere for one but never got my hands on one ;)

Is this one spring loaded ?

you realise the idea of it is to allow airflow to the intercooler when at speed, not to subvert speed cameras. Speed cameras in NSW take your photo from BEHIND so how would flipping down your front plate help that? also, unless you have a big and deep opening on your front bar like the one in the pic then your number plate wont be folding anywhere...

i also fail to understand why you cant just floor it to your chosen 160kph cruising speed, then slam on the brakes and drive past the camera at 55kmh then accelerate back up to 160kmh. if you can't see 3 2 meter wide signs on the road side then you have bigger problems than speeding fines.

if you want to be able to speed through cameras then just take your plates off and drive around with out them.

well the law states that the number plate has to visible from 45 degrees in any direction, so if it folds it so it can't be seen from looking down at 45 degrees then it would be illegal.

just like the factory alloy tray on a nissan patrol. you can't see the number plate looking down from 45 degrees so technically its illegal.

well the law states that the number plate has to visible from 45 degrees in any direction, so if it folds it so it can't be seen from looking down at 45 degrees then it would be illegal.

just like the factory alloy tray on a nissan patrol. you can't see the number plate looking down from 45 degrees so technically its illegal.

NUTS !! :O There goes that idea.......

Hmm, I wonder how difficult it would be to use the factory drop down spoiler motor to drop a panel infront of the plate, you would only need to obscure part of the number so its difficult to tell what it is... covers up the plate above 80 then disappears when you pull up... ah mischef :O

My mate has one on his GTR

cop was in front of him ,pulled him over and asked him to push on it

he was more impressed at the whole thing rather then wanting to book him

he asked my mate what its purpose was and when my mate told him he said what if you go thru a red light

he made him put the screw back in it so it couldnt flip under

problem solved

top idea i say

yeah.. nsw speed camera's take photo's from the back anyways..

i only like it because i rekon it looks cool and would be a cheap little "i've got a free weekend mod"

for all you people thinking this is a good idea to do illegal things with... why dont you just take ur plates off...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...