Jump to content
SAU Community

Recommended Posts

The standard Ferrari Enzo not good enough for you? Why not have it customised by Pininfarina.

post-20773-1155824398.jpg

Most collectors would be happy enough to just own a Ferrari — any Ferrari.

There wouldn't be many who would feel the need to remodel one, let alone a top-of-the-range Enzo worth close to $2 million.

Computer modelling was used to help design the P4/5, the shape of the Enzo being altered to take on the domed roof, rear wing and rear exhaust outlets of the 330 P4.

More than 200 components were especially made for the car.

The body is made from carbon fibre, and the entire turret is a single-shell windscreen cut to accommodate butterfly-wing doors.

The whole project probably cost Glickenhaus about $8 million.

And an interview with the owner.

Link to comment
https://www.sau.com.au/forums/topic/130719-why-mess-with-perfection/
Share on other sites

I think it looks pretty cool. But for that money... that an Aston, Porka GT, Porka 997 turboS, Ford GT, big arse house, small unit up the coast, small unit down the coast, and invest the rest so you dont need to work again.

I think ferrari is such a wank.

They have cars that cost around 350,000 for a base model and then have factory options like "Handling package" and "brake package" It's a Ferrari you'd think they'd turn and stop pretty well out of the shop.

wank factor = 11 well call me a wanker cause i would swap my skyline for it anyday .good luck to bloke for daring to be different and if ya can afford the 8 mill why would ya give a rats arse what anyone else thought i know i wouldnt lol

lol.. no seriously, good on him for investing his time and effort into his passion, i wish i could make my own custom supercar

... but still that thing is so ugly it makes the original enzo look good

So what he should have done is invest in a BN Body Kit, 24" chrome Zeptana's and some pulsing neons maybe ?? :O:D

There's a Chop project for you ................ :)

Is it just me or does a stock enzo look better

Each to their own I guess, but I with you Lee. I prefer the "stock" Enzo.

Not that it matters because pics on the internet is the closest I'll ever come to owning one :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...