Jump to content
SAU Community

Recommended Posts

hi all,

i did a quick search, and now im trying to figure out if it was a genuine m spec nur that i saw this morning. apparently there arent very many in the country, and someone was saying in another thread that there was an imitatin m spec going around in qld, but this thing seemed pretty genuine to me.

anyone know if the owner is on here? they were qld plates too by the way (i left a couple of numbers in the plate). also had buddy club p1 rims, and a large exhaust tip, about 4.5 inch id say.

i saw it in boronia, on my way back from dropping my car off for an alarm install. it pulled up next to my sis's car at the lights, i didnt see the "M Spec Nur" badge until it took off, and went past.

only got one crappy photo on my phone (was a bit difficult for my sister 1.7L renault to catch it:P), and you cant see the farking m spec nur badge properly, but you can still kinda see it...

r34_m_spec_nur.jpg

well, it was absolutely awe-inspiring. i was impressed when i thought it was a gtr, then when i saw the spec nur badge, i had to get my head around the fact that this is the car ive been fantasizing over, looking at pics on the net. i never thought id randomly see one on the road. :(:(

Yep, It's Michael's, it is genuine. Just got off the truck from QLD on Friday and I went for a spin in it. It's very nice. Was taken to Vic Roads to change reg on Friday. It will hopefully be at the Show and Shine in December.

It's going into Race Pace today to have some work done to it.

I've attached pics I took on Friday when he brought it in to my work.

post-8874-1156126362.jpgpost-8874-1156126384.jpg

Yep, It's Micheal's, it is genuine. Just got off the truck from QLD on Friday and I went for a spin in it. It's very nice. Was taken to Vic Roads to change reg on Friday. It will be at the Show and Shine in December.

it's going into Race Pace today to have some work done to it.

I've attached pics I took on Friday when he brought it in to my work.

post-8874-1156126362.jpgpost-8874-1156126384.jpg

nice!! i saved the pics, and noticed they are titled "mines r34" so has it been tuned up by mines? :( ZOMG teh awesome!!1!11! if it has :(

blur plates for him? or you think he wont mind? :)

whats different about it vs normal bnr34 ?

300kmh speedo, gold build plate, metallic gold paint on rocker cover, timing cover

Optional Millenium Jade paint scheme

N1 engine specs: features

Metal BB turbos

N1 spec block

N1 spec pistons, rings, conrods, all balanced

N1 oil pump with relief valve

N1 high flow water pump

N1 exhaust manifold and turbo flanges

N1 cold air duct

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...