Jump to content
SAU Community

Recommended Posts

Well GTST25 was correct I looked at the turbo and it was only being held on by two nuts and they where loose also put two more nuts on and made sure they where on tight this time and she is all good :(

PS Does anybody know anything to stop this from happening again?

I know its cheap to get more nuts but I dont really want to keep replacing them every 3 or so months

Edited by 7yphon

something just happened to my turbo on my r33. When engine is revved and boost is starting to build up it makes a screaming noise, sounds something like an external gate. Its loud, sounds alright but i doubt it can be good for the turbo, took the intake pipe off, very very little shaft play back and fourth and turbo spins perfect, very free spinning also no chips on blades.

My 32GTR has a whistle noise all the time from 800 rpm to redline. I can hear it through the centre vents. I think it's from the Turbs but I cant determine what it is if its not even spooling (r34 N1's). Mech thinks the front turbo has a problem.

Like another post I'm going to wait until something drastic happens but sure would like to know for certain what it is.

PS. the engine has just been rebuilt - it was there before and it's there now.

i have the same high pitched noise coming from my car

it comes around from the turbo area side but im not sure when u listen close up it sounds like the other side

couple of people told me its normal and its possibly the powersteering pump

i just checked the 4 bolts and locktabs on the turbo and they are very tight.. im guessing its powersteering pump that needs replacing or its just normal and im getting paranoid :D

my noise happens when the car is warm, after a decent boost, then at idle you hear it whining and when you rev to 1500-2000rpm the whinding goes louder, but then u take it for a drive again and it disappears, then comes back and then disappears.. not to sure what to expect

anyone else had this and replaced powersteering pump?

Tiesto:

Do you have a front mount?

A mate of mine has a 4 door R32 and it made a noise like that turned out to be the Air passing through the Intercooler Pipes

LTHLRB:

I wouldnt because if the tubo is just hanging off you could make the turbo worse thats what Ive been told by Turbotech.

Sinister32:

I know what you mean can fix whats not broke right?

Mate i had a nasty squeal from my engine bay once. Couldn't find a boost leak, bad belt or anything. Then i realised i had some broken exhaust studs, started to fix these and realised the the turbo had come loose from the manifold (no idea why ??? bought the motor from a wrecker in sydney had it fitted by a mechanic) and the squealing noise was the pressure coming out from between the join. Long story short removed the turbo replaced the gasket and bolted it back together and wala :(. This noise was only on 3/4 to full throttle. Went heaps better after that, no shit :P haha

i have the same high pitched noise coming from my car

it comes around from the turbo area side but im not sure when u listen close up it sounds like the other side

couple of people told me its normal and its possibly the powersteering pump

i just checked the 4 bolts and locktabs on the turbo and they are very tight.. im guessing its powersteering pump that needs replacing or its just normal and im getting paranoid :sick:

my noise happens when the car is warm, after a decent boost, then at idle you hear it whining and when you rev to 1500-2000rpm the whinding goes louder, but then u take it for a drive again and it disappears, then comes back and then disappears.. not to sure what to expect

anyone else had this and replaced powersteering pump?

I have this one, my mechanic has explained the whine to me a while ago and ive kinda forgotten what he said, but something about the cams have now become worn in and its getting stuck doing its variable valve business when its idleing... Nothing to worry about he recons.

Worst explaination... ever.

well that might explain it cheers mr italy, i might get someone to take a look at it

ive also noticed that on my exhaust manifold there was a snapped stud (the last stud which is closest to the firewall), and the nut and half the stud fell out today upon further inspection... so now the other half of the stud is in there, i plan to fix that asap but i doubt its related as i dont have a exhaust leak, just a whining sound >_<

yer I have a stud missing from the man when I was changing the turbo back last year, When I removed the heat shield the nut and half the bolt fell off, I was like dam better fix that but doesnt seem to have made a dif so meh.

There are a few things this that makes noises that the f**king shitty thing you have to just try and go through the list until its gone :blush: at least you know most of the part that where replaced are new lol.

Edited by 7yphon
  • 1 year later...
mine does exactly the same started doing it once i put on a pod so im guessing its because of the way the air goes through the pod at that particular point causes a whistle its definatly not a problem or because anything is shagged and i wouldnt be doin any major component changes to fix it

Ahh! What is this noise (rb25 r34) Loose bolts turbo? Yep! Did them up, Ahh! Still there, Hint: does it on idle, tap the accelerator, gone?? Hard to find but seems to be seals on throttle motor (tract control) when engine is finally hot and under vacume there's that squeely noise. Anyone had this one before??? Cars done 94000klms just started. Those Whitty People with the flashy lights pulled us over "Whats under there mate a dead Cat" HA HA didnt even know what he was looking at any way. $79 Part of 2007 Label still affixed (I was going to scratch it off eventually), $200 Didnt like My HKS Induction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
×
×
  • Create New...