Jump to content
SAU Community

Recommended Posts

Can someone check this car for me? If you can tell me where to get the program myself that'll be better than bugging people to decode for me.

http://www.carsales.com.au/pls/carsales/...4&make_id=5

VIN: 6u9000bnr34

Cheers

Can someone check this car for me? If you can tell me where to get the program myself that'll be better than bugging people to decode for me.

http://www.carsales.com.au/pls/carsales/&a...4&make_id=5

VIN: 6u9000bnr34

Cheers

you need the last 6 digits of the VIN for that.

i got this programme and used iton a r33 im i nthe process of buying... apparently the 2 door manual is actually a 4dr auto??? the caryard guarantees it is all genuine though? is it possible that the vin was swapped back in japan and once here the compliancers had no idea? or is it more likely something dodgy has happened while in aus.

thanks.

  • 5 weeks later...
i got this programme and used iton a r33 im i nthe process of buying... apparently the 2 door manual is actually a 4dr auto??? the caryard guarantees it is all genuine though? is it possible that the vin was swapped back in japan and once here the compliancers had no idea? or is it more likely something dodgy has happened while in aus.

thanks.

It could be a simple case of transposing a number when you ran the VIN through FAST. Post it up or try it again for yourself just to double check.

ER34021493

post-24887-1196381265_thumb.jpg

Model: R34

Series: 25GT

Built: February 1999

Colour: Athlete Silver

Body: 4 door sedan

Transmission: 4 speed auto

I ran my vin through Nissan FAST to look for the part number for the a/c compressor and it came up with two different a/c compressors with different part numbers.

Does this mean that they are both compatible with my car?

Can anyone help me out?

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...