Jump to content
SAU Community

Recommended Posts

I had a problem with the rear passenger door glass hitting the hard rubber surround along the top edge whenever I shut the door with the window up.

This would always cause an air leak sound even at low speeds. So I had to lower then raise the window everytime the door was opened.

Stagea, in their infinite wisdom, put in adjustment screws to help with this problem and the following was my attempt to fix the glass level.

post-25601-1158241205.jpg

Screwdriver shows where to prize off the door handle plastic surround - On the top front edge.

post-25601-1158241333.jpg

Picture of the back of the plastic surround shows the single clip.

post-25601-1158241549.jpg

Underneath is the mounting screw for the panel. 10mm socket works easier than the phillips screwdriver. The rest of the panel comes off by simply pulling around the edges to release the clips. A short, sharp yank with your finger tips is all that is required. See pictue below for where the mounting holes are situated.

post-25601-1158241720.jpg

Be sure to disconnect the electrics - a small screwdriver is needed to release clip, then slide out.

post-25601-1158241862.jpg

All off and admiring the view. Plastic weather protection will need to be removed along the top edge to get at the level adjustors. Pull gently on the plastic without stretching it out of shape and it will stick back into place.

If you look carefully, you'll be able to see the holes where the plastic mounting clips go - so you'll know where to pull on the door trim. Check out the quality of those speakers - the factory must have spent a whole $5 on those babies! And $1 on the foam.

post-25601-1158242015.jpgpost-25601-1158242348.jpg

This picture shows the level adjustors with increments. You can see by the worn ring mark in the paint where it used to be and how far I had to drop the glass. There are two adjustors - one for the front edge and one for the rear. I only needed to adjust the rear to fix my problem.

post-25601-1158242097.jpg

This picture shows the little cloth pads that the glass runs against when moving up and down.

They can also be adjusted to change the angle of the glass on the 'in and out' plane - if that makes any sense. I believe they need to be left with a reasonable amount of play in them as the window changes angle as if feeds up and down. Keep these clean or you will scratch the glass.

The best position to have the glass is where it will just pop under the edge of the hard plastic surround on the body without getting caught on it.

I hope this help you enjoy noiseless motoring and to avoid breaking something unnecessarily.

Happy tinkering,

Warren

Edited by 3intheBack
Link to comment
https://www.sau.com.au/forums/topic/134380-rear-door-window/
Share on other sites

Beatuful, GREAT writeup! This might get lost in the Stagea section, so you might want to think about having it moved to the DIY section, either way, I am putting a link to it in the "Mega Stagea Link" thread :)

Again very nice writeup! Thanks!

  • 1 year later...

i did it the other day but i cant remove the damn plugs to the power controls. How did you unplug it? the side morrow adjuster can be unplugeed easy but not the power window one. Lemme know. thanks

Yudy

  • 1 month later...

All the electrical plugs use the same locking system. You need to push in the little clip on the side. Use a screwdriver are similar. It can be a prick of a job as you need two hands to unplug it and two hands to hold the door fab.

  • 1 year later...
i did it the other day but i cant remove the damn plugs to the power controls. How did you unplug it? the side morrow adjuster can be unplugeed easy but not the power window one. Lemme know. thanks

Yudy

Having this same problem, driver's side front on S2... power controls plug (the big one) doesn't matter how far the locking tab is depressed, it's stuck like glue. Yet I know it's not glued 'cause I plugged it in myself not 4 months ago.

  • 3 years later...

We had been having trouble with window alignment of the left rear door window glass in our S2 for a while.

Recently i had the door to a point where i could make some minor adjustments and then i found the alingment problem for our car.

I found that there is a small white plastic bush that slides in the glass runner, which the regulator arms are mounted to via a little metal balljoint. I found that plastic bush was split in half and allowing the glass to lay back.

I have been into Nissan and i was told that i can't even buy a new complete regulator.

Has anybody found this same problem and be willing to share a solution.

Cheers, Jason.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...