Jump to content
SAU Community

Recommended Posts

I got 201.3 rwkw with 651 Nm torque after having my SAFC-II tuned yesterday im happy with it the car feels great

what i want to know is this a good figure for the following mods.

HKS Pod Filter

HKS 3.5" Cat Back Exhaust + 4.5" HKS Muffler

HKS EVC 5 boost controller @ 10psi

Apexi SAFC-II + Tune

Greddy Type R Blow Off Valve

600x300x76 Autobahn88 Intercooler 2.5" piping

Sard Fuel Pressure Regulator

Walbro 500hp Fuel Pump

NGK iridum sparkplugs @ .8mm gap

BP 98 pump gas

Factory: turbo, ECU

Dyno sheet below

dynosmallgp9.jpg

Link to comment
https://www.sau.com.au/forums/topic/134528-got-a-dyno-tune-yesterday-2013-rwkw/
Share on other sites

Yeh solid result, plenty more power to be made with a aftermarket computer as your A/F reading is floating around a bit. and a bit of fine tuning of your EBC.

Edited by BezerkR32
Yeh solid result, plenty more power to be made with a aftermarket computer as your A/F reading is floating around a bit.

yea the air fuel ratio is sitting between 11.8 and 12 max at the higher rev range.

Looks like a good result.. How's it feel - what was it before they started tuning??

it was 185 rwkw going way rich after 4000rpm

the car feels much more solid mid and top end. is also much smother and fuel economy is better also.

im pretty happy i was hoping for 215ish but hey im on my way.

:D

Put the cars on the same dyno, on the same day, then compair. That figure is too high in my opinion, especially without a aftermarket ecu, only a cat back exhaust and 10psi :happy:.

mad082, your figure is really unbelievable. Maybe go to the next dyno day in your state, this will give you a fair comparison with other cars and will tell you if your mechanic is "tweaking" the figures :sick:

a dyno is simply a measuring tool for improvement and tuning. comparing one dyno read out in one state to another in another state could be like comparing, well, apples and oranges?!

do more mods to the car and see the improvement that each makes and then u will be heading in the right direction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...