Jump to content
SAU Community

Recommended Posts

This was my 2nd time at the drag strip.

i am happy to get into the 14's as my other best was 15.06

What do you think of my Drag slip

Reaction Time 0.117

60' Time 2.31

1/8 Time 9.67

1/8 kmh 124.49

1/4 mile Time 14.78

Trap Speed 156.31

any comments tips trick would be great

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yea 201.3rwkw with a Manual trans.

the Drag racing thing is not as easy as it looks haha

i was launching at 3500rpm and dumping the clutch and then changing to 2nd as quick as possible to stop wheel spin.

Edited by r33madd

Disregarding the time, the trap speed of 97mph (converted) means you don't have anything close to 200rwkw. With that kind of power you should be expecting at least 105mph, and probably closer to 110mph.

Then again your run wasn't done on a Dyno Dynamics but still, that dyno that was used seems pretty optimistic.

That 60 footer is pretty horrible.

Backing of a little instead of changing to second might be better. This is what i do, the RB just feels so much happier in the high revs.

With a pod, boost controller and cat back exhaust,

I managed a 13.6 with a 60 footer of 2.0....

14.78 is half a second slower then the official time for an r33 gts-t isnt it?!?!

Go back again with better tyres.

What tyre pressure do most of you use.

What Revs is a good level to launch at.

Whens the best time to change gears

What 60ft time would i need to get a low 14 or a high 13

and when you say backing off a bit wouldnt that hert my time even more.

from the look of your sig the rear of your car is too low... very hard with the IRS to get traction when it's that low, no room for squat or weight transfer

also are you running any kind of fuel controller? if you are running those mods off the stock ecu it will be way too rich, esp. with an aftermarket pump in there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...