Jump to content
SAU Community

Recommended Posts

This was my 2nd time at the drag strip.

i am happy to get into the 14's as my other best was 15.06

What do you think of my Drag slip

Reaction Time 0.117

60' Time 2.31

1/8 Time 9.67

1/8 kmh 124.49

1/4 mile Time 14.78

Trap Speed 156.31

any comments tips trick would be great

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yea 201.3rwkw with a Manual trans.

the Drag racing thing is not as easy as it looks haha

i was launching at 3500rpm and dumping the clutch and then changing to 2nd as quick as possible to stop wheel spin.

Edited by r33madd

Disregarding the time, the trap speed of 97mph (converted) means you don't have anything close to 200rwkw. With that kind of power you should be expecting at least 105mph, and probably closer to 110mph.

Then again your run wasn't done on a Dyno Dynamics but still, that dyno that was used seems pretty optimistic.

That 60 footer is pretty horrible.

Backing of a little instead of changing to second might be better. This is what i do, the RB just feels so much happier in the high revs.

With a pod, boost controller and cat back exhaust,

I managed a 13.6 with a 60 footer of 2.0....

14.78 is half a second slower then the official time for an r33 gts-t isnt it?!?!

Go back again with better tyres.

What tyre pressure do most of you use.

What Revs is a good level to launch at.

Whens the best time to change gears

What 60ft time would i need to get a low 14 or a high 13

and when you say backing off a bit wouldnt that hert my time even more.

from the look of your sig the rear of your car is too low... very hard with the IRS to get traction when it's that low, no room for squat or weight transfer

also are you running any kind of fuel controller? if you are running those mods off the stock ecu it will be way too rich, esp. with an aftermarket pump in there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah nice idea, you mean to suction it to the gauges? I hadn't thought of that.
    • A few suggestions: Do you have the option of retarding your exhaust cam gear to bring the power band over to the left? VCT would be turned off after you make peak torque, you see the power/torque will decay faster with it left on all the way to the limiter Once VCT is turned off, you'll find the motor will take a bit more timing being ramped in Send its mum, more boost! Of course, depends on your exhaust pressure.
    • Tow a boat... people won't know wtf is going on 🤣 
    • I was back on the dyno again yesterday after completely revamping my methanol injection system. I was making 440kw at 19psi. Great, this is more then I was making last summer with my old meth system at that pressure, and I figured it would be smooth sailing up to 30+psi. We continued increasing from there and by 25psi, I had only hit 455kw. Dyno sadly lost utility power at this point and I left. We seemed to be on course to hit the same power wall as last summer (477kw@27psi). This is a built RB25 S1 stroked to a 2.8. Built and ported head with Kelford 272/262 cams. Precision 6466 Turbo. Tuner last year believed the power wall is a mix of RPM limitations (Hydro lifters/Limit set at 7600RPM) and fueling. With my new meth system, we're seeing zero knock now but it still won't go up.  What else can I do at this point? Here's my train of thought.  - It's clear from the dyno graph that I would easily make power to 8500+RPM but I'm limited to 7600RPM. I could risk increasing my limiter, but hydro lifters have me worried. What are my options here besides going NEO head or solid lifter conversion? I'm rocking a 1.05AR turbine on my 6466. Would dropping down to a .84 help shift that power down in anyway? - We're only seeing roughly a 30kw difference at the top end with VCT on or off. Is this normal? I want to confirm VCT is working properly. - Should I look into other cam options?  - Should I just keep increasing boost and see if she wakes up later on? I would expect to hit 600rwkw around 35psi with my 6466.   
×
×
  • Create New...