Jump to content
SAU Community

Recommended Posts

damn i am keen but i have already made plans is there one on next week?

would be good to get it organised and have a few more lines up there together.

I would really like to have a few runs before i do my cam gears and clutch

Test 'N Tune is on tonight.. I'm headin out for the first time.

No reason stopping me tonight. Wheather so far is holding up.

so we can expect you to update you sig from "Willowbank Quarter Mile: Yet to be done."

to "Willowbank Quarter Mile: 9 secs" tomorrow hey :P

Edited by ZENNON
I suggest you do your clutch before you go, just ask Col-GTSX how badly it sucks.

Standard Clutch and 200rwkw = Fryed clutch and a 24 second pass at 50mph... :laugh:

Exedy Custom and 240rwkw = 12.4@111mph (street tyres)

Yeah i actually burnt my clutch during the burnout (2nd gear burnout). When i left the line the car went no where and the revs went through the roof. I ended up droping it into 2nd and crawling away and i go up to about 80kph i think as my top speed on that run... ;)

My traction and suspension was absolutely shit.

was getting rear end bumping on take off, to i ended up takin off a bit slow till i hit 5,000rpm and then hit 2nd gear and just took off.

1st one i didnt do my gear changes all to well

2nd one i did them alot better.

low mph were cause of bad traction (shit tyres & shit stock suspension).

BZZZT Wrong. With your setup you should have a great big whack of top end regardless of wheelspin off the line.

With a 2.6 60' my old 180 would still pull 111mph and smash into the 12's.

Stock suspension is doing you a favour over drift-spec coilovers so you can't blame that either.

I'd be looking at how you launch and when you change gear. Either that or you don't have the power you should - which is what your MPH tells us.

was it fairly busy? would of hoped to get more than 2 runs

hmmm i have taken on board everyones views on the clutch thing

Im surprised about your time as your car seemed fairly quick the other night

ohh well good work trying and not just being a talker!

and remember you can always improve!

The tyres are shit. I'm actually due for new ones. Plus the tyres on the rear are absolutely shit anyway, shouldnt even be using them on the quarter mile or qld raceway.

With the suspension. If i allow wheel spin, the rear end is just jumpin up and down non-stop till i take my foot off the accelorator and then re-gain traction and then take off a bit smoother.

After talkin to dan. Pineapple bushes will help this but there could be other factors involved causing the rear end to jump up and down such as the diff or suspension.

The plan right now is - replace suspension with ISC coilovers (they are new on the market and little has been said, so i'd be happy to give these guys a go and see what happens).

Next, after that is a new turbo with external wastegate and high mount manifold.

With the mods i've done already, the car should be putting out around 250kws. I'm only getting 215kw's and when on the dyno, something is restricting us back which we dont know.

Last tune, we started off and got 296hp and after several times of playing around with the mapping on the powerfc, we kept loosing 1 or 2 hp even though we Matt Spry was properly tunning it giving it more in some areas of the injector maping, etc.

Guess one thing I should be finding out is if there is any leaks anywhere and start doing some testing on the engine (compression, etc). Alot I think needs to be done before I look at the turbo upgrade though.

So your saying that you had axel tramp? Its a bitch aint it? getting off the mark was my hardest part as the other cars were flogging me there even though I gained on them up the strip, I put it down to practice and setup and working out the right tecnique. 13.7 btw 3 times.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...