Jump to content
SAU Community

Recommended Posts

Ok currently got my RB25DET out of the car, rebuild starting next week hopefully.

So far in parts ive got

Arias Forged Pistons

Cometic .74" thick Metal Head Gasket

New Bearings, Seals & Gaskets

Tomei IN&EX Poncams

Tomei Cam Gears

Iv also got to put on one the motor is run in

Garret GT30R 500hp internally wastegated turbo

Apexi PowerFC & Hand Controller

Nismo 555cc Injectors

Bosch 040 Fuel Pump

Now i wanted to know while im rebuilding the motor if i should get some SCAT rods and ARP studs, i am hoping for max 300rwkw and run daily on 200-250rwkw. Im wondering how strong the stock bottom end is on the RB25DET and if i need rods or can i get away with the stockers.

GTR Rods are what you want, with good rod bolts.

You dont need to fork out for big $$$ rods, no need.

$400 at the absolute worst, so they are very cheap, and extremely worthwhile, good for 300rwkw easily.

I HAVE ARIAS PISTONS & THE RINGS ARE SHOT AFTER ABOUT 25000 KLM THE RINGS ARE SHIT GET SOME TOTAL SEAL RINGS TNT TYPE INSTEAD. I HAD THE SAME SETUP AS YOUR ABOUT TO DO A I GOT APPROX 260RWKW @ 18 PSI GOOD LUCK

GTR Rods are what you want, with good rod bolts.

You dont need to fork out for big $$$ rods, no need.

$400 at the absolute worst, so they are very cheap, and extremely worthwhile, good for 300rwkw easily.

haha I picked up a set of GTR rods in excellent condition for $90.

What sort of power could I push them to?

Surely std rb25 rods will hold 300rwkws. Normally at that stage pistons are first to go unless the tune is spot on. Im in the process of putting my rb25 back together as well. ACL pistons though. Im also only gonna be around 250rwkws max 300. I have same headgasket and similar bolt ons. Im using std rods and bolts and if someone says to change to GTR ones im gonna kill someone cause those stupid farking spiral locks are a goddamn prick to put on and i really dont wanna do it again :laugh:

Edited by r33_racer

Do you wanna find out if they will hold it forever? :laugh:

Possibly not on the standard bolts... its not really proven over a long period

Its really just a case of...

Motor is apart, the rods are filthy cheap... why not change em for a couple hundred! Cheap insurance if ive ever seen it.

Yeah Id go the GTR rods with new ARP bolts. I had mine shot peened, resized and linished - but for all that you can buy new forged rods. So prob just use the GTR rods with new bolts.

ACL and there double spiral locks - what a pain in the arse they are.

I HAVE ARIAS PISTONS & THE RINGS ARE SHOT AFTER ABOUT 25000 KLM THE RINGS ARE SHIT GET SOME TOTAL SEAL RINGS TNT TYPE INSTEAD. I HAD THE SAME SETUP AS YOUR ABOUT TO DO A I GOT APPROX 260RWKW @ 18 PSI GOOD LUCK

Some one didnt let them bed in properly :(

30psi, 500rwhp on arias piston... they work!

GTR Rods are what you want, with good rod bolts.

You dont need to fork out for big $$$ rods, no need.

$400 at the absolute worst, so they are very cheap, and extremely worthwhile, good for 300rwkw easily.

you tell me? ur the one referring GTR Rods..

man ur quick on the replies, respect! :(

i HAVE read the first post, im just answering ur question to why i was talkin about the bottom end being good for 300rwkw..

now we can all go and stick our heads in a canape and sing kumbaya!

:S

man ur quick on the replies, respect! :(

i HAVE read the first post, im just answering ur question to why i was talkin about the bottom end being good for 300rwkw..

now we can all go and stick our heads in a canape and sing kumbaya!

:S

Dan, ill have a race for you if you ever come up to Darwin again, lol. On a safe tune what kind of power could i expect, this has already blown way out of budget so if im looking at 250 to 270rwkw then i prolly wont bother with rods. Also had timing belt replaced 300km before motor leaned out, so would the standard Nissan timing belt be ok.

GTR rods definately be a better decision because for the price you can get them it's a safer decision, it's what I'm getting! Sizing & balancing while it's all getting done at once too. Also a N1 oil pump instead of a standard one would be a decent upgrade as well.

I also had my timing belt replaced about 2000k's before mine popped, but I've been told a heavy duty belt would just be a safer option, also good while it's there & opened :(

Dan, ill have a race for you if you ever come up to Darwin again, lol. On a safe tune what kind of power could i expect, this has already blown way out of budget so if im looking at 250 to 270rwkw then i prolly wont bother with rods. Also had timing belt replaced 300km before motor leaned out, so would the standard Nissan timing belt be ok.

Haha damien your funny, brodie told me yours poppped, do not get hi tech to tune it lol. and my power goals are a bit more than your mate lol. got a whole new set up now lol. just buy a gates timing belt mate thre 110 bucks and good investment.

things to definatly get:

idler tensioner; $100

new bolts for the idler tensioner: $15 (very imporatant to replace)

get race bearings too

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...