Jump to content
SAU Community

Recommended Posts

This recent sydney heat has had an impact on the smooth/responsive feel of my car.

Obviously 9psi boost has turned into more like 7 or 8 due to the heat, which i expected.

I'm using the stock intercooler (R33 - 3inch full exhaust - pod - turbotech set at 9psi)

The car has stalled on cold start 3 times on the 3 recent hot days, and the idle was playing up a bit while driving, dropping way too low (will look into cleaning aac valve soon).

Also, the car seemed alot less responsive, less willing to pick up on demand, kind of running rougher.

Never had any of these issues before the heat. Since it's cooled down again, everything seems fine.

My question: Is all this related to the hot weather? If so, will a fmic fix this?

Link to comment
https://www.sau.com.au/forums/topic/139057-is-the-hot-weather-to-blame/
Share on other sites

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

yeh, in hot weather my line turns into a freggin corolla.

lol great, take one skyline, some extreme heat, mix together vigorously, and you get one corolla.

what about the stalling? my car always starts first go, i barely have to look at the key and it's rumbling nicely.

but the last time (sat), i was cranking it over forever, and on the 4th attempt it started.

i had a cooler on my 33 and went throught the same shit munkeh... so i have a two part answer to your question:

a) cooler makes little, to no difference on start up problems... and

b) you should have a cooler anyways, can runs so much better with one

turboz just dont like the heat... i used to find that on really hot days, it just didnt have the low down pull i usually had

an intercooler wont help you much at all. its just going to act as a heat soaker when your in traffic. since your in sydney, this would be more then likely the case. on that note, my car also feels like poo lately especially in the 30+ degree's we've had here in the last few days.

k, well i feel a bit better now, knowing you're all suffering with me :(

so you reckon the cold start problems might have been related to the heat. maybe from the previous day's heat abuse or something?

best way to get decent performance in summer is a waterspray intercooler jet. I have had great sucess with this.

I had a cefiro a couple of years ago that was set up for drift and saw a lot of track work in summer and it was also my daily driver.

I had a temp probe lust before the throttle body to measuer intake temps.

When I first got the car in summer with the stock cooler I saw temps of 60deg + then I put the FMIC on and saw an drop of about 10 to 15 deg.

but I was getting pinging on really hot days. so I decided to fit a waterspray system. All it really was was a windscreen washer motor/bottle with a hose going to the front of the cooler that directed 4 water mist nozzles on the front of the cooler. It had a check valve to stop it from siphoning out of the washer bottle. It was triggered by a pressure switch from an old washing machine that was set to 4psi.

As soon as you started to boost it the system would switch on and spray water in a fine mist onto the cooler. It was amazing it dropped intake temps to about 5 to 10 deg above ambient. and stopped the engine from pinging. I am going to do the same mod this summer on my new car and will do a writeup for those interested. All up it cost about $70 for the patrs and a bit of fiddling but its a really good mod. you just have to remember to fill up the bottle every time you fill the car as it only lasts for about a 300k's with spirited driving on a small scource.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...