Jump to content
SAU Community

Recommended Posts

Dan,

thanks for your reply about the CAS... That helps answer the question big time!

Also, I have just loaded up the haltech software on my work pc, coil dwell time can be set between 0.2ms right up to 20ms.

....

This is 'tested' on Version 1.11.1 of ECU Manager.

I know they are constantly adding new things to the software + ecu's with each update.... so it may have not always been in there.

post-49724-0-37608100-1352433077_thumb.png

Standard dwell on left, max on right for illustration purposes.

Using a R32 / R33 Platinum Pro base map to work off

Yeah you can set dwell time but can only choose one figure for the entire rev range.

In something like a Wolf V550 you can set coil charge time over RPM and also over battery voltage. It has a full tuning table for both at 125RPM intervals

Quick voltage vs rpm for ign. dwell.

Obviously not as detailed down to every ~125rpm or there abouts as some ecu's can do but it's still able to do same basis.

I should probably have gone a bit further than using single axis of RPM and moved into the full map to cover more values.

edit - stupid me not attaching. fixed.

post-49724-0-88270600-1352434206_thumb.png

Edited by Force Fed

As per text mate. Am happy to see if i can find anything else that may have been added since yourself / Sean had a look. :)

At least they are bringing out new "features" on same hardware!

You got a promotion, Nick? From auto-sparky to car assembly? Haha.

At least you've got a project to work on.

im auto lek/mechanic now man... once i finish this car and finish building these new ones ill be into the workshop full time. instead of goin from 1 side to the other

Everyone should stop talking about finishing their cars off and actually do it :)

I want to do some more photo's

Edit.jpg

Took the fitting out of the filter/cooler housing on my block today, going to go chasing a replacement male to male fitting for it on monday for my oil cooler. Was going to relocate the filter but have decided I don't really need to and dont really have the room

Am thinking about doing a catch can setup but. just deciding on how to do it

umm autobarn actually sell some decent quality parts... and the price isnt even that bad (depending on what u buy)

doesnt matter what shop it is. its not nice seeing it go up in flames. specially when 4 little cun7s lit it up

Yeah jokes aside its not real cool at all, the fact that it was young girls setting fire to a toy shop a few weeks from christmas makes it pretty horrible

When I was 12 I never would have dreamt of doing that, Parenting these days has taken a slide for the worst

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...