Jump to content
SAU Community

Recommended Posts

Last night the Hobbies in the Hills, hobby shop above UAS was completly destroyed by fire. The fire did not get down stairs so except for being very wet, UAS survived. My car was getting its clutch replaced and I was lucky enough along with all the cars to get out without a problem. I dont think it is known if UAS will be ok but John has a lot of cleaning up to do!

Link to comment
https://www.sau.com.au/forums/topic/140230-uas-almost-burnt-down/
Share on other sites

Theis stock should be Ok but stuff like computers, phones and paper work will be gone.

The bigger issue will be the chance they will have to re-locate because of the dammage to the upper floors might make the building a write off!

Theis stock should be Ok but stuff like computers, phones and paper work will be gone.

The bigger issue will be the chance they will have to re-locate because of the dammage to the upper floors might make the building a write off!

Thats a really shitty situation - glad nobody was hurt all the the cars were safe.

Im watching the footage of the fire on TV right now :P Thats one serious blaze

actually apparently one of the fire fighters was injured :P

you would have to expect a hobby shop would go off like an H bomb. all that flamable glue, pressurised spray paint, model rocket engines, heaps of RC car fuel = KABANG with a side dose of KABOOM!

Does anyone know how the blaze started? I really feel for John as he is going to get reamed through no fault of his own.

actually apparently one of the fire fighters was injured :P

you would have to expect a hobby shop would go off like an H bomb. all that flamable glue, pressurised spray paint, model rocket engines, heaps of RC car fuel = KABANG with a side dose of KABOOM!

Does anyone know how the blaze started? I really feel for John as he is going to get reamed through no fault of his own.

According to the reports on Sky news, the cause is yet to be determined, but rest assured, that building is completely forked and will no doubt need to be demolished.

from website

---------------

URGENT NEWS

Due to fire in adjoining premises you may find it difficult to contact us at the moment.

You can fax us on 9634 8888 or email [email protected]

The phone no 9634 8000 has been diverted to one line so there may be delays until the problem is rectified.

If you have must talk to us, and are unable to do so please call 0425 303 019.

--------------

:P:D :D

feel for john and co

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...