Jump to content
SAU Community

Recommended Posts

when i give the car a boot from 2nd gear i sometimes notice smoke in my rear view mirror, i got the car tuned a few months back and everything was fine, so i'm just wondering if i should be worried or not, btw, i hardly ever even boot the car most of the time i drive normal, i don't know if this could be the reason.

last few months i used motul chrono 300v, and two days ago i switched to turbo light 4100, even before i started using these oils i would sometimes notice the smoke, it doesn't always happen.

thanks

the mods i have

pfc

fmic

cai pod

bleed valve

3inch exhaust - full

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/140801-smoke-when-booting/
Share on other sites

i might aswell add this here instead of making another thread, For the first time earlier on tonight when i gave the car a boot from second a small orange light flashed a few times to the right of the speedo, i then checked the knock and it read 65, the car pulled good, iv just never seen this light come on when driving, this was the first time. Also since i got the car retuned i haven't got any high knocks, this was also the first high knock

Do you have a catch can fitted? preferrably externally vented, if you must plumb it back, make sure its properly baffled

blow by is something that alot of people seem to overlook

And personally I would be taking the car back to the tuner and asking him to recheck the tune, it may just be that your plugs are not up to task, or some other cause - but if you are suddenly getting higher than normal knock, something is amiss and your tune may need attention.

no i don't have a catch can fitted, is it important?, just before the tune i got new irridium plugs put in, the tuner double checked them to see if they were gaped correctly every thing was fine

THrow the iridiums away personally... Heard of quite a few RBs misfiring and carrying on with iridiums in.

Also, white/grey smoke, can also be oil from the turbo.

Blue smoke is BURNT oil ( In combustion ) white/grey can be oil getting around the seals in the turbo and straight into the exhaust, so it's not actually burning, but vapourising.

If you don't beleive me. Go heat some oil in a sauce pan (Don't get it explosively hot) but a fair bit hot, and watch the smoke that rises.

from what has been described, its not turbo seals.

Hulk 1010, a catch can is very important, and so often overlooked.

It stops crank case gasses (blow by) being recirculated through the intercooler, but more importantly stops oil from blow by going into the combustion chamber. Blow decrreases the intercooler efficiency, and can cause detonation.

The harder you lean on an engine (more power) the more blow by you will get.

RBs do breath a fair bit, especially so if you use too light an oil - 3g 5w50

The smoke coming out of the exhaust - from what you've said, sounds pretty normal - the high knock reading is worth getting checked.

Instead of listening to everybody on here - take it to your tuner/mechanic and let them sort it. Without seeing the smoke first hand, its pretty damn hard to say for 100% certain, if you have something to be worried about or not.

thanks for all the replys

Iv been looking at a few catch cans on various sites, what would a reasonable price be for one? the ones from overseas appear cheaper but i don't really want to wait a long time for the product to arrive, also i'm not sure about the hosing size.

thanks

these are some of the ones iv come across

http://www.nengun.com/catalogue/search/

http://www.slidingperformance.com/catalog/...amp;x=0&y=0

The greddy square type can be opened, and you can put filling (copper wire scourers work well) in them to catch the suspended oil particulate from the blow by - would be my recommendation

The come with all the clamps, quality hoses and mounting brackets and are great quality

cusco type would be fine if you are not plumbing it back in, but external vented is NOT street legal

your choice :D

i was driving around a bit earlier on, about 25 mins in is when i saw the smoke

9:04pm... Thats night time.

Don't use the revision mirror at night to tell if you are blowing smoke or not as it always looks as if you are, especially with head lights behind you.

Get the other half to drive the car and you drive behind. Best and most accurate way to test. Providing she is familiar with the car and isn't freaked to boot second. :D

I've always seen a slight haze in the revision mirror when booting it at night with the person behind with their lights on.

from what has been described, its not turbo seals.

Hulk 1010, a catch can is very important, and so often overlooked.

It stops crank case gasses (blow by) being recirculated through the intercooler, but more importantly stops oil from blow by going into the combustion chamber. Blow decrreases the intercooler efficiency, and can cause detonation.

The harder you lean on an engine (more power) the more blow by you will get.

RBs do breath a fair bit, especially so if you use too light an oil - 3g 5w50

The smoke coming out of the exhaust - from what you've said, sounds pretty normal - the high knock reading is worth getting checked.

Instead of listening to everybody on here - take it to your tuner/mechanic and let them sort it. Without seeing the smoke first hand, its pretty damn hard to say for 100% certain, if you have something to be worried about or not.

After reading the mods done to the car & reading these comments I'd have to say this does make perfect sense. I've got a friend with an S14 who had to put a catch tank in after similar mods as he was loosing stacks of oil (Partly to do with the fact that he couldn't turn boost below about 16 PSI!) Catch tank cured his issues. Surprised the workshop hadn't suggest you fit one too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...