Jump to content
SAU Community

Recommended Posts

Hi everyone,

I did a quick search for “oil pressure” but as I am posting under major panic I didn’t come across anything that was relevant to my problem.

As I am currently running my motor in (trying to clock up 500km) I have notice oil pressure drop. I realize that a bit of drop is ok but today when I was at the lights I noticed that the pressure was getting awfully close to 0 on my oil pressure gauge and kept hovering below 2. As I pulled into my driveway I notice the gauge went right down to 0. I quickly switched the engine off to prevent any damage.

My question to the general populus here in FI section is: Is this a normal occurrence? Can anyone hazard a guess to what the problem might be?

Any help will be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/142836-oil-pressure-getting-close-to-0/
Share on other sites

is the "low oil pressure light" on?

No light isn't on.

get an aftermarket gauge.. 1/100th of the price of a new engine

You are right; I'm going to look in to getting one now

before you do anything else, get yourself a new oil pressure sender unit.

Do you believe my sender could be shot? If so I’ll get one from Nissan.

Do you believe my sender could be shot? If so I’ll get one from Nissan.

if its an r32 then it very well could be.

it seems to be a common problem with them.

and as Waz has stated, getting an aftermarket gauge is best (but you'll need a sandwich plate etc). so go with the new sender unit first.

try spray the sender unit with that contact cleaner stuff..

after my engine was put bak in my car i had a similar thing.. when the car was hot the oil needle would sit on like 1psi at random times. the sender unit was all oily and decrepid looking.

go have a read on www.aus300zx.com in the technical pages.. they have a big writeup about changing the OPS (oil pressure sender unit)

many of them changed their unit only to have it fail again after 6 months...

my setup:

gauge (ebay) comes with sender unit - $30-60 depending on what brand

sandwich plate - $25 from justjap

i mounted it in the glovebox. still can use the stock gauge for hte oil pressure warning light (which is accurate)

plus its WAY more accurate than the stock gauge

good investment me thinks

Yeh i had the same problem and i shit myself, on idle after driving for a long time it would drop to just above 1 on the guage but the light didnt come on which was good.

But then i used different oil and it doesnt do it anymore haha, still gets low sometimes though.

I think most 32s have shotty oil pressure guages.

BTW new engine as well with 1,000km on it. New guage is on the agenda.

Thanks everyone for all your help.

I purchased an Autometer oil pressure gauge that I am going to install tomorrow. I'll let you all know if it works. Just one last question though, at what PSI should my oil pressure gauge be reading at idle?

When cold ive seen it around approx 70 psi at idle

When warm around approx 24-25 psi at idle

Thanks champ! I'll use that as a reference point

Please be aware, the standard nissan oil pressure guage reads in KG/cm^2 not PSi.

Yea, I have disconnected the standard one now and installing the Autometer which is in PSI. Thanks for the heads up though!

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...