Jump to content
SAU Community

Recommended Posts

if it comes in the kit, then probably. make sure you check if the dump pipe mates up with the stock one.

but as soon as you fit, youll boost it up, hit r&r and then youll post up why your car runs like poo. so best you do some research on all of the mods you will to make it work correctly and get the best out of it.

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2680426
Share on other sites

if it doesnt come with lines, you will have to make up new ones and a silicon elbow off the turbo to the intercooler pipes. Also depending on the size of the front cover you may need to make a new induction pipe...

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2681062
Share on other sites

I already have everything nessary to run the turbo just wanted to no if it would fit with out to many problems so it shouldnt r+r as i dont have the stock computer and yes i know ill have to tune it just wanted to know about the fittment thats all

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2681108
Share on other sites

Well in that case yes it will bolt straight on there, as my 3037 pro s did, the only thing you will have to worry about is the dump pipe/front pipe to cat position and most likely going to have to custom on, part from that good luck, i think thats the answer you were after?

and of course you do know that you have to change the lines part from that it does bolt on

Thankyou

adam

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2681485
Share on other sites

Just wanted to know if a hks 2835 pro s will bolt straight up to a rb 25 ?

if you buy the kit!

it comes with everything you need.

also it doesnt need a gasket from the turbo to the dump, i went around in circle with hks tring to get one, 1st they sent me the wrong 2 gasket then in the end they finally said OHHH GT2835 PRO S that doesnt need a gasket at all ahah!

awsome turbo i see full boost under 3500rpm

if it doesnt come with lines, you will have to make up new ones and a silicon elbow off the turbo to the intercooler pipes. Also depending on the size of the front cover you may need to make a new induction pipe...

umm mine come with all lines (braided), metal intake pipe, silicon thingso and also the elbow from the turbo to the i/c (also inc silccon thingo and i little clamp which has like a heatshield over the silicon joiner thingo) + a nice hks heat sheild

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2682062
Share on other sites

' date='17 Nov 2006, 10:24 PM' post='2682062']

awsome turbo i see full boost under 3500rpm

Mine doesnt really hit its swing till 4grand. what boost are you running? I think mine can see 19psi by 4grand, then falls to 16-17. Although you can really feel the torque coming on just after 3grand.

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2682972
Share on other sites

Mine doesnt really hit its swing till 4grand. what boost are you running? I think mine can see 19psi by 4grand, then falls to 16-17. Although you can really feel the torque coming on just after 3grand.

im only running 16psi with a very very safe tune (11:1 afr)

i want to do headgasket and cams and increase the boost to the 18psi see if i can come close to 400rwhp

Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2682985
Share on other sites

As everyone else has said, they are a great turbo, Brought the kit. Straight bolt on with no problems what so ever. Have just fitted cams and Plazmaman plenum. Have to go an get a tune asap.

Edited by woolls
Link to comment
https://www.sau.com.au/forums/topic/143645-hks-2835-pro-s/#findComment-2683353
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...