Jump to content
SAU Community

Recommended Posts

wtb

R32 disk rotors. Set of front and rear or let me know if u have a pair. Just need cheapys to get it going. Aslong as they have meat im not fused on slotted or std

Skyline braided brake lines to suit 32 calipers

R32gtr rear swaybar

Anyone wana swap 25mm bolt ons for 15mm ones? Hubcentric of course

Thanks

Matty if u can get hold of a couple of panel filters this is going cheap

http://page10.auctions.yahoo.co.jp/jp/auction/m75373880

nengun sell them new for 140ish shipped, but im tryin to work out which 2 i need, the kit says a B and a C, but the model indicator highlights and A and a B :S

wtb:

part of the rb25 loom where it plugs into the alternator.. my end has broken off so i need to solder a new end on..

rb25det intake manifold to head. i need 2 of the bolts that bolt the manifold onto the head.

cheers

wtb

R32 disk rotors. Set of front and rear or let me know if u have a pair. Just need cheapys to get it going. Aslong as they have meat im not fused on slotted or std

Skyline braided brake lines to suit 32 calipers

R32gtr rear swaybar

Anyone wana swap 25mm bolt ons for 15mm ones? Hubcentric of course

Thanks

Adrian try getting some HEL braided lines to suit R32 off ebay....they are $160 something and work well

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...