Jump to content
SAU Community

Recommended Posts

As the topic states, I got a question about when the car is launched. At times, I have launched it from about 4k revs - this has given the best grip, and the actual take off is very smooth and controllable. However, I was in a friends r33 today, and the launch was done at 6k. The strange thing is, there was no wheelspin, but the rear of the car did momentarily dip downwards as the car started to move forward.

Is this normal (the dipping of the rear)? I guess those who have taken their car to the drags etc - is this what normally happens or the car is not supposed to dip at all?

Link to comment
https://www.sau.com.au/forums/topic/143809-launching-the-skyline/
Share on other sites

yes, all the weight transfers to the rear wheels, and compresses the suspension, and because all the weight is on the rear wheels, you get much better traction. many drag cars run soft suspension in the rear, and very firm in the front to aid this. sounds like your mates car has better tyres than yours also...

many drag cars run soft suspension in the rear, and very firm in the front to aid this.

Other way round. Making the front take longer to return from full extension in the shock aids weight transfer - ala 90/10's. Stiffer rear suspension in IRS cars like Skylines stops the tyre from toeing in and decreasing the contact patch at launch.

i launch at 5,500 - 6,500 rpm and dont have much of a traction problem but takes a bit to keep straight off the line, slicks will top it off on a good launch :)

on the street a 5,000 rpm launch with soft throttle is pretty good.

Edited by LTHLRB

good suspension? and i dump the clutch.. i ride it out at 6,000rpm still spins a little bit, but does launch well.

And as for traction. a 6,000rpm launch on street tyres got me a 1.9 60 footer. :P

Kinda odd that any of you can launch anywhere near 5000+rpm in a gts-t and not get wheelspin....

My car isn't overly powerful at 205rwkw, and there is no way it could launch at 5000rpm without a shit load of wheelspin on street tyres....

Even when it was stock, 5000rpm, and dumping the clutch, or even letting it out slower, would still spin the wheels with ease.

Maybe in a GTR....but really don't see it happening in a GTS-T

same...

evan with new tyres i get the same thing.

ive tried heaps of diff ways of doing it to, like using the handbrake, riding her etc etc..

I have the whiteline/bilstein suspension kit, its not exactly setup for drag racing, but id imagine it should be better than stock stuff.

wouldnt realy of thought its possible doing it at like 5-6000rpm...

Kinda odd that any of you can launch anywhere near 5000+rpm in a gts-t and not get wheelspin....

My car isn't overly powerful at 205rwkw, and there is no way it could launch at 5000rpm without a shit load of wheelspin on street tyres....

Even when it was stock, 5000rpm, and dumping the clutch, or even letting it out slower, would still spin the wheels with ease.

Maybe in a GTR....but really don't see it happening in a GTS-T

Once I get my turbo back exhaust system in place I want to take my car for a run down at wsid and see what it can do... But I have a question being that it is an auto would it be better to go from 0 or launch at like 2,000rpm... on stock everything apart from the exhaust once it gets done. Oh and yeah its a 4 door R34 GT-T if that makes any difference.

Maybe someone fryed the clutch?

I think it was a gradual throttle application - I would like to try it myself, but I dont know if my clutch will take it - and as it is, i think the clutch might be on its way out.......

i dont have much experience with this, but even 4k sounds a bit high to me.

if i go at 3k, hold the clutch just at the sweet spot (on the verge of engagement), for only a couple of secs (it starts to smell of burning), i still get some wheel spin.

but my suspension is too hard, and so every bump causes my tyres to lose contact with the road.

but 5k? sounds like a burnout to me. lol

Edited by Munkyb0y

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...